background image

 

 2 of 7

 

For accurate installation, proper operation, and years of satisfaction, please read and 

understand the installation and owner

s manual fully prior to installing the console.

 

 

From all of us at Curtis, we thank you for choosing our product

.

 

WARNINGS, TIPS, & REQUIRED TOOLS

 

INSTALLATION

 

1.

 

Vehicle Preparation:

 

 

1.1   Installation of a Dome Light, Strobe Light, or Rear Work 

Lights requires the removal of the plastic roof. If 

installing any of these accessories, remove the plastic 

roof as outlined in the accessory instructions.

 

Note:  If 7.5

-

amp fuse was installed in vehicle when installing 

wiper, switch back to 15

-

amp fuse.

 

 

2.

 

Dome Light and/or Strobe Light pre

-

wiring:

 

 

(skip to step 3 if not installing either of these)

 

2.1   Poke up through the headliner with a screwdriver or awl 

at each of the 2 smaller holes in the windshield support.

 

Note:   Poke the holes from the headliner side up through the 

hole in the roof to avoid having the headliner pull away 

from its glued surface.

 

2.2   Install the end of each Tether from the Console into the 

Windshield Support and allow the Console to hang.  See 

figure 2.2.

 

Note:  If an interior mirror is installed, remove the mirror from 

the mounting bracket.

 

2.3

  

 Cut the cable tie from each of the two coiled wires inside 

the console.

 

 Be careful to not cut any wires.

 

 Feed each 

wire through the hole in the roof directly above the 

wire.

 

 See figure 2.3.

 

Note: Leave the corresponding wires coiled if not installing a 

strobe light or dome light. 

 

• 

Orange/ black for Dome Light through center right.

 

• 

Yellow/black for Strobe Light through center left.

 

Fig. 2.2

 

Cable Tethers

 

Fig. 2.3

 

Yellow/Black

 

For Strobe Light

 

Orange/Black

 

For Dome Light

 

• 

#1 (small) Phillips screwdriver

 

• 

3/8”, 7/16”, 1/2” 

open

-

end wrenches or sockets

 

• 

5/32” 

and 

3/16” 

Allen wrenches or drivers

 

TOOLS REQUIRED:

 

  driver and passenger.

  Curtis accessory weights are listed in product

  add additional weight to the base vehicle. All

  Curtis Cabs, blades and general accessories

ADDED

WEIGHT

  brochures. Deduct the accessory's total weight

  from the vehicle's rated capacity and never

  exceed the vehicle's rated capacity including

 

 

 

Exposure to Carbon Monoxide can Cause illness, 
serious injury or death.  

Never operate vehicle if suspi-

cious of Carbon Monoxide.  Inspect exhaust system for leaks 
monthly.  Leaks can result from loose connections, corrosion, 
cracks or other damage to the exhaust manifold.  If leaks are 
found, repair or replace exhaust system.  Do not use vehicle 
until repair or replacement is complete.

 

WARNING

 

Содержание 47587420002








Отзывы: