Curtec Packo Скачать руководство пользователя страница 5

 

Packo manual 

2020-7 

 

03

 Use 

 

 

 

 

Filling 

The temperature of the content cannot exceed 70°C. The content 

has to cool down to 30°C before the container can be closed. The 

drum can be closed according to instruction 1. 

 

 

Freezing 

Packo is made of plastic which is resistant to a minimum 

temperature of -25°C. As of -5°C, shock load on the containers 

should be avoided. 

 

 

Attention!

  The volume of containers filled with water-based 

contents can increase by 10%. The chances that containers will 

distort are real and it will reduce the stability of a container stack 

on a pallet. Please maintain a maximum filling level of 90% and 

test the stability of a pallet stacking. 

 

Air transport 

During air transport, the pressure drops inside a plane’s cargo 

hold, which causes air inside a package wanting to escape. After 

landing, normal atmospheric pressure prevails again which, 

depending on the amount of escaped air*, can cause the drum 

wall to cave in. 

 

CurTec packaging has not been designed to compensate pressure 

differences. The construction is such that a correctly closed 

packaging allows air to escape relatively fast, but does not allow it 

to return easily. 

 

Since CurTec has no influence on the use of its packaging by end 

users, they advise to test each transport mode. 

 

It remains the responsibility of end users to verify whether a 

package and content comply with relevant transport regulations. 

CurTec refers to the regulations mentioned in the UN certificates. 

 

* The quantity depends on the content type (the shape and air between) and the 

filling degree/ level

 

 

Содержание Packo













Отзывы: