Cumberland PNEG-240 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 76

background image

6. Installation

26

PNEG-240

Chain Feeding System

Clean Out Cover Installation

The clean out cover (B) should be located the section of trough nearest to the return side of the hopper.
Using a 2" hole saw, cut a hole centered in the bottom of the trough as shown in

. It is important

to cut the hole as centered as possible in order to prevent a corner of the chain to catch on the hole which
could possibly result in costly repairs. Place the clean out cover (B) under the clean out hole (A) and
tighten the thumb screws to secure it in place.

(See Figure 6J.)

Figure 6J

Installing the Chain

When all trough ends are fully inserted and tightly fit into the couplers, corners and hopper, you are ready
to install the chain. Start by removing the belt guard from the feeder and remove the shear pin from the
power sprocket. This will enable you to turn the sprocket freely during chain installation.

(See Figure 6K.)

Figure 6K

Ref #

Description

A

2" Clean Out Hole

B

Clean Out Cover

«
...
24
25
26
27
28
...
»

Содержание PNEG-240













































































Отзывы:

Нет отзывов

Похожие инструкции для PNEG-240

Бренд: Balanced Body Страницы: 4

Бренд: Velocitek Страницы: 81

ABS-Lock X-Flat

Бренд: ABS Страницы: 8

ABS-Lock X-DURCH

Бренд: ABS Страницы: 8

Бренд: ABS Страницы: 8

Бренд: Federal Signal Corporation Страницы: 12

Бренд: Mackie Страницы: 18

Бренд: Mackie Страницы: 2

Бренд: Mackie Страницы: 8

Бренд: Mackie Страницы: 7

Бренд: Nabtesco Страницы: 26

Бренд: Tar River Страницы: 44

Бренд: Tar River Страницы: 61

Бренд: VDO Страницы: 15

Бренд: VDO Страницы: 20

ULTRATHERM 908i

Бренд: gbo Страницы: 32

Бренд: Dantel Страницы: 6

Бренд: Zero 88 Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды