Cumberland 36

Part No. 4801-5401 Rev 1/15 

36" 48" & 52" Funnel Flow Fan 

– Unassembled 

Page 2 of 12 

 

Warnings 

Warning! 

Disconnect All Power Sources Before Installing This Equipment.  Failure To Disconnect Power Source 

Can Result In Property Damage, Serious Injury Or Death! 

 

Warning! 

Dangerous Rotating Machinery!  Keep Hands, Clothing, Etc. Clear When Operating! 

Do Not Operate Without All Guards And Covers In Place!

 

 

Warning! 

All Wiring Should Be In Accordance with National Electrical Codes Or Other Local Codes. 

 

Warning! 

The  Installer  Is  Responsible  For  Complying  With  All  Relevant  Regulations,  Such  As  National  Wiring 
Regulations  And  Accident  Prevention  Regulations.    Particular  Attention  Must  Be  Given  To  The  Cross-
sectional  Areas  Of  Conductors,  The  Selection  Of  Fuses  Or  Other  Protection,  And  Protective 
Earth/Ground Connections! 

 

Warning! 

The Voltages In The Power Cables And Certain Parts Of The Drive Can Result In Death.  Whenever The 
Drive Has Been Used It Must Be Isolated And Disconnected For 5 Minutes Before Any Work Commences 

 

Danger! 

Only Qualified Electrical Personnel Familiar With The Construction And Operation Of This Equipment And 
The  Hazards  Involved  Should  Install,  Adjust,  And/Or  Service  This  Equipment.    Read  And  Understand 
This  Manual  In  Its  Entirety  Before  Proceeding.    Failure  To  Observe  This  Precaution  Could  Result  In 
Severe Bodily Injury Or Death! 

 
 

!

 

!

 

!

 

!

 

!

 

!

 

Содержание 36" Funnel Flow Belt Drive Fan













Отзывы: