background image

43

42

5.  M: Wireless Flash Shooting  

with Manual Flash

This describes wireless (multiple shooting) using manual flash. 

You can shoot with a different flash output setting for each slave 

unit (firing group). Set all parameters on the master unit.

1

 

 Setting the flash mode 
to  < M >

  Press the < 

MODE 

Button to set the flash to 

M mode.

2

  

Setting flash output

  Turn the Select Dial to set 

the flash output of the 

groups.

3

  

Taking the picture

  Each group fires at the set 

flash ratio.

6.  Multi: Wireless Flash Shooting  

with Manual Flash

1

  

Setting  < Multi >  strobo-
scopic flash.

  Long press the < 

MODE 

button for 2 seconds so 

that <

Multi 

> is displayed. 

Long press the < 

MODE 

button for 2 seconds again 

to exit.

2

  

Setting flash output/flash 
frequency/flash times.

  Setting the flash output/

flash frequency/flash 

times in the A group. Set-

ting the multi flash mode. 

(see Page 38)

  B and C group can only 

control the ON/OFF of the 

slave unit by pressing the 

MODE 

> Button.

Using a flash (master/slave) with a radio transmission wireless 

shooting function make it easy to shoot with advanced wireless 

multiple flash lighting, in the same way as TTL autoflash shooting.
The basic relative position and operation range are as shown in 

the picture. You can then perform wireless TTL autoflash shooting 

just by setting the master unit to < 

TTL 

>.

Slave/Master Unit‘s Positioning and Operation Range

Autoflash Shooting with One Slave Unit

•  Use the supplied mini stand to position the slave unit.
•  Before shooting, perform a test flash and test shooting.
•  The transmission distance might be shorter depending 

on the conditions such as positioning of slave units, the 

surrounding environment and weather conditions.

Transmission distance is about 30m.

Wireless Multiple Flash Shooting

You can divide the slave units into two or three groups and 

perform TTL autoflash while changing the flash ratio (factor). In 

addition, you can set and shoot with a different flash mode for 

each firing group, for up to 3 groups.
•  Auto Shooting with Two Slave Groups

•  Auto Shooting with Three Slave Groups

FR36_BDA_Nikon 171005.indd   42-43

06.10.2017   15:10:52

Содержание CUlight FR 36N














Отзывы: