Culligan G1 Series Скачать руководство пользователя страница 32

Страница: 32 / 142

Culligan® Series G1 Reverse Osmosis

Cat. No. 01021713

Wiring for Softeners and Filters with MVP Controller

For these systems, you must add a 24V relay P/N 01016156, to provide the pretreatment contact.
MVP to Relay: Connect a wire from Terminal 5 of the relay to the left terminal of P8 (Aux 2) on the MVP circuit board.

Connect another wire from terminal 1 of the relay to the right terminal of P8. Refer to

Figure 18.

Relay to GBE RO controller: Connect a wire from the POSITION (J2), PIN 3 terminal on the AUX board to terminal 3 on

the relay. Connect another wire from the POSITION (J2), PIN 4 terminal on the AUX board to terminal 4 on the relay.

Relay

LCD

SW6 Dip Switch

Comm

Flow

Meter

Aqua

Sensor

Cam

Aux2

Aux1

P7 Sol

Valve

P9 Power

2.5VAC 24V

Motor

P11

Battery

GROC BOARD

MVP

Figure 18.

MVP to GBE RO controller relays.

Содержание G1 Series















































































































































Результаты поиска

Содержание G1 Series

Отзывы:

Culligan G1 Series, Инструкция по установке, эксплуатации и обслуживанию, Страница: 32 / 142

Результаты поиска

Содержание G1 Series

Отзывы: