manualshive.com logo in svg

Culligan G1 Series, Инструкция по установке, эксплуатации и обслуживанию, Страница: 125 / 142

Поделиться
Скачать
Culligan G1 Series Скачать руководство пользователя страница 125

Basic Principles      

121

Cat. No. 01021713

Appendix B  Basic Principles

Reverse Osmosis

In order to understand reverse osmosis, we must first define osmosis. Osmosis is the passage of a liquid through a 

semi-permeable membrane. A semi-permeable membrane is a membrane which allows one component of a solution to 

pass through it and not the others. In osmosis, there is a tendency for a liquid to go from an area of less concentration to 

an area of more concentration through a semi-permeable membrane. Figure 74 shows the osmotic process.

Figure 74. 

 Osmotic process.

If pressure is applied to the concentrated solution, reverse osmosis will take place. The pressure causes a flow through 

the semi-permeable membrane into the dilute solution. The semi-permeable membrane acts as a barrier to ions and does 

not allow them to pass through into the dilute solution. When applied to water, this means that the product water has a 

reduced total dissolved solids content as a result of the passage of water molecules through the membrane while the 

mineral ions are rejected. See Figure 75.

Figure 75. 

 Effect of pressure on reverse osmosis.

Rejection and Recovery

Feed water entering the system is split into two streams, a product stream and a concentrate stream. See Figure 76.

Figure 76. 

 Feed water product stream and concentrate stream.

During the process of reverse osmosis, some of the water has its dissolved solids content reduced by approximately 99%. 

This high quality product water is sent to service.
The rest of the feed water contains the dissolved solids removed from the product water, in addition to the dissolved solids 

already present in the feed water. This concentrate water is sent to drain.

Содержание G1 Series















































































































































Отзывы:

Нет отзывов