Cuisinart SPB-8 Series, Инструкция и книга рецептов

Страница: 6 / 20

6
To crush ice: The ReMix6.0 600-Watt Blender motor
is strong enough to crush ice without liquid at any
speed; however, for your convenience, we have preset
the best speed for ice crushing. To crush ice, place ice
cubes in the blender jar. Press the On/Off button. The
On indicator light will illuminate. Press the Ice Crush
button until ice is crushed to desired consistency.
Blender will cycle through function and shut off when
complete.
To pause or stop blending process:
a. To pause blending process:
Push the button corresponding to the speed at
which you are currently blending. For example:
If you are blending on High speed, push the
High speed button and the blender will stop
blending but the unit will remain on.
b. To stop blending process:
Push the On/Off button when you are finished
with your recipe and would like to turn the
blender off.
c. To prevent excessive stress to the motor:
Your blender incorporates an auto-stop feature.
After running continuously for two minutes, the
blender will automatically revert to Standby
mode. To continue blending, press the desired
function.
To dislodge food:
Use a rubber or plastic spatula
to help remove food lodged around the removable
blade assembly. Do not use spatula until you have
turned the blender off. Replace the cover and
measured pour lid and continue blending, if nec-
essary. Make sure spatula is not inside the blender
jar before blending.
To reset the unit: This appliance features an
advanced resettable thermal fuse. In the event
of an overload condition, the unit will shut down
to protect the motor from overheating. To reset
the appliance when this happens, unplug the unit
and let it cool for a minimum of 15 minutes. Then,
reduce the contents of the blender jar and/or clear
any jams. Restart the unit as noted in the operat-
ing directions.
When finished blending: Press the On/Off button
and unplug the blender from the electrical out-
let. Never remove the blender jar from the motor
base until the blender is off. Do not remove blade
assembly from blender jar when removing jar from
motor base. Simply lift blender jar from motor base.
Do not put hands into blender jar with blender
plugged in.
CLEANING AND MAINTENANCE
Always unplug your Cuisinart
®
ReMix6.0 600-Watt
Blender from the electrical outlet before cleaning.
The blender is made of corrosion-resistant parts that
are easy to clean. Before first use and after every
use, clean each part thoroughly. Periodically check
all parts before reassembly. If any part is damaged
or blender jar is chipped or cracked, DO NOT USE
BLENDER.
Remove the blender jar from the motor base by lifting
straight up and away. Remove blade assembly by
turning counterclockwise.
Remove the blade assembly. Wash in warm soapy
water, rinse, and dry thoroughly.
CAUTION: Handle the blade assembly carefully. It is
SHARP and may cause injury. Do not attempt to remove
blades from assembly.
Remove the blender jar cover and the measured
pour lid. Wash in warm, soapy water; rinse and dry
thoroughly, or place in upper rack of dishwasher. The
blender jar must be washed in warm, soapy water
and rinsed and dried thoroughly. The blender jar can
also be placed upside down in dishwasher.
Finally, wipe the motor base clean with a damp cloth
to remove any residue, and dry thoroughly. Never
submerge the motor base in water or other liquid, or
place in a dishwasher.
Tip: You may wish to clean your blender blade
assembly as follows: Squirt a small amount of
dishwashing liquid into assembled blender jar and fill
halfway with warm water. Run on Low for 15 seconds.
Repeat, using clean tap water. Rinse and dry all parts
thoroughly.
Any other servicing should be performed by an authorized
service representative.