8
9
SETTING THE AUTO ON TIME
When you enter the AUTO ON time set mode, the
previously selected AUTO ON time, or the default time
(12:00) will flash.
1. Press and hold the AUTO ON button until the
display begins to flash.
Use the Hour and Minute
buttons as above to program your start-brew time.
2. Press the AUTO ON button once to confirm the
set time and activate the program.
The white light
will illuminate, indicating the AUTO ON function has
been activated. LCD will display the current time.
NOTE:
Be sure to set any additional preference
before the AUTO ON cycle begins.
3. AUTO ON brew cycle begins
and the LED will
turn off. The Carafe and Brew white indicator lights
will illuminate when the brew cycle begins at the
time you have selected. When the brew cycle is
complete, Brew indicator light will turn blue,
indicating the unit is in Keep Warm mode. Lights will
turn off when the Keep Warm cycle ends.
NOTE:
To start brew time at the same time the next
day, simply press and release AUTO ON button once
more. The white AUTO ON light will turn on.
SETTING THE AUTO OFF TIME
Press and hold the AUTO OFF button until the display
is flashing. Use the Hour and Minute buttons as above
to program your coffeemaker to shut off from 0 to 4
hours after brew cycle is finished.
MAKING COFFEE WITH
WHOLE BEANS
Follow instructions in Setting Up Your 12-Cup
Coffeemaker on page 8.
1. Insert charcoal water filter
Follow directions for the preparation and insertion of
the filter on page 8.
2. Fill the water reservoir
Open the reservoir cover and pour in water, using
the water level window indicator to measure the
number of cups desired.
NOTE: Do not exceed the 12-cup line. Doing so
could cause carafe to overflow.
3. Add Beans
Lift the grinder basket lid, using the recess on either
side. Fill the basket with the desired quantity of
beans and replace lid.
NOTE: Use 1 level scoop (1 tablespoon) of
whole beans per cup. For 1 to 4 cups, use 1½
level scoops per cup. Do not add more than 14
scoops. This could cause the grinder to mal-
function and/or the coffeemaker to overflow.
4. Insert Coffee Filter
Press the filter basket door release button to open
door and place either a paper filter OR permanent
filter in the basket.
• Paper Filter – Place a basket paper filter in the
basket, making sure the filter is completely open and
touching the side walls and bottom of basket.
• Cuisinart’s Commercial-Style Permanent Filter
– Be sure the filter handle is facing away from the
grinder basket, so it does not interfere with the flow
of ground coffee into the filter basket.
NOTE:
Some ground coffee may flow into
the carafe.
5. Put Filter Basket in Place and Close Filter Door
6. Before brewing
Make sure the glass carafe is in position on the
heater plate and the top cover is closed. Plug the
cord into an electrical outlet.
NOTE
: This coffeemaker is equipped with a safety
interlock system, which prevents the unit from oper-
ating if the cover is open or the grinder cover is left
out. If you try to turn the unit on with the cover open,
the carafe indicator will flash continuously until the
missing parts are installed and you close the lid.
If you open the cover during the grinding process,
CHARCOAL
WATER FILTER
INSERTING THE WATER FILTER
1. Remove the filter from the polybag and soak,
fully immersed, in cold tap water for 15 minutes.
2. Lift the water filter holder out of the water
reservoir of the 12-cup coffeemaker side.
3. Press down on the filter compartment and pull
toward you to open.
4. Place filter into the holder and snap closed.
Be careful – improper placement can tear the
filter skin.
5. Flush filter by running cold tap water
through holes in bottom of compartment
for 10 seconds.
6. Allow the filter to drain completely.
7. Slide the water filter holder back into the chan-
nel in the water reservoir, pushing down to the
base of the unit.
NOTE:
Repeat steps 1–7 above on the single-
serve side.
NOTE:
We recommend changing the water filter
every 60 days or after 60 uses, and more often if
you have hard water.
Replacement filters can be purchased in stores,
by calling Cuisinart Consumer Service, or at
www.cuisinart.com
SETTING UP YOUR
12-CUP COFFEEMAKER
INITIAL CLEANING
Perform an initial cleaning before making your
first beverage. Follow these instructions, without
adding coffee.
1. Insert charcoal water filter. Follow directions for the
preparation and insertion of the charcoal water filter
on the left.
2. Fill water reservoir.
3. Make sure carafe is in place.
4. If you haven’t already, plug the power cord into
an independent outlet. When the coffeemaker is
plugged in, the unit will automatically turn on.
5. Press the Carafe button once to enter Carafe
Brew Mode. Press the Grind Off button to
deactivate the grinder.
6. Press the Brew/Off/Auto Off button once and allow
the brew cycle to run until it is complete.
7. The one-time cleaning process is complete. Discard
hot water. Your coffeemaker is ready to use.
PROGRAMMING YOUR
12-CUP COFFEEMAKER
SETTING THE CLOCK
When the coffeemaker is plugged in, 12:00 will flash in
the display for 10 seconds, indicating the unit is in Time
Set mode. If 12:00 stops flashing, simply press and
hold Hour or Minute button to return to flashing Time
Set mode. Hold buttons down to scroll through the
digits, or press and release to advance one digit at a
time. When scrolling, the numbers will advance slowly
and then speed up. When the number displayed
approaches the desired time, press and release to
advance one digit at a time. Be sure the PM indicator is
on if a PM time is desired.
ssgb1_20ce074398_ib_eng_final.indd 8-9
ssgb1_20ce074398_ib_eng_final.indd 8-9
11/13/20 9:50 AM
11/13/20 9:50 AM