Cub Cadet V469 21

12

For repairs beyond 

the minor adjustments 

listed here, contact 

an authorized service 

dealer. 

6

Trouble 

Shooting

Cause

Problem

Remedy

Engine fails to start

1.  Blade control disengaged.
2.  Spark plug wire disconnected.
3.  Fuel tank empty or stale fuel.
4.  Fuel valve closed.
5.  Faulty spark plug.
6.  Blocked fuel line.
7.  Engine flooded.

1.  Engage blade control.
2.  Connect wire to spark plug.
3.  Fill tank with clean, fresh gasoline.
4.  Open fuel valve. See engine manual. 
5.  Clean, adjust gap, or replace.
6.  Clean fuel line.
7.  Wait a few minutes to restart.

Engine runs erratic

1.  Connect and tighten spark plug wire.
2.  Clean fuel line; fill tank with clean,  

fresh gasoline.

3.  Clear vent.
4.  Drain fuel tank. Refill with fresh fuel.
5.  Refer to engine manual.
6.  Refer to engine manual.

1.  Spark plug wire loose.
2.  Blocked fuel line or stale fuel. 

3.  Vent in gas cap plugged.
4.  Water or dirt in fuel system.
5.  Dirty air cleaner.
6.  Carburetor out of adjustment.

Engine overheats

1.  Fill crankcase with proper oil.
2.  Remove blower housing  

and clean.

3.  Refer to engine manual.

1.  Engine oil level low.
2.  Air flow restricted. 

3.  Carburetor not adjusted properly.

Occasional skips 

(hesitates) at 

high speed

1.  Adjust gap to .030”.
2.  Refer to engine manual.

1.  Spark plug gap too close.
2.  Carburetor idle mixture adjustment 

improperly set.

Idles poorly

1.  Reset gap to .030” or replace  

spark plug.

2.  Refer to engine manual.
3.  Refer to engine manual.

1.  Spark plug fouled, faulty, or gap  

too wide.

2.  Carburetor improperly adjusted.
3.  Dirty air cleaner.

Mower will not  

mulch grass (If 

Equipped)

1.  Do not mow when grass is wet; wait 

until later to cut.

2.  Mow once at a high cutting height, 

then mow again at desired height or 
make a narrower cutting path.

3.  Sharpen or replace blade. 

1.  Wet grass.

2.  Excessively high grass.

3.  Dull blade.

Uneven cut

1.  Place all four wheels in same  

height position.

2.  Sharpen or replace blade.

1.  Wheels not positioned correctly.

2.  Dull blade.

Excessive

Vibration

1.  Cutting blade loose or unbalanced.

2.  Bent cutting blade.

1.  Tighten blade and adapter. Balance 

blade.

2.  See an authorized service dealer.

Mower will not  

self propel

1.  Check belt for proper pulley installation 

and movement.

2.  Stop engine, disconnect spark plug 

wire, and clean out debris.

3.  Inspect and replace belt. 

1.  Belt not installed properly.

2.  Debris clogging drive operation.

3.  Damaged or worn belt.

Содержание V469 21"





















Отзывы: