Cub Cadet Pro2B+ 21120902 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 38

background image

Position the top assembly P#(A2110) above the upper
frame assembly with the Rubber Dust Guard positioned
towards the seat as shown in Figure 2-7. Fasten the top
assembly to the upper frame assembly using (2) 5/16”-
18 x 2-1/2” HHCS P#(K0125) and (2) 5/16”-18 nylon
flange locknuts P#(K2516). Leave the locknuts slightly
loose, to allow the top assembly to open and close
easily. Refer to Figure 2-7 for hardware location.

Secure the (2) lower mount tubes P#(B0752) to the rear
frame using (2) 5/16”-18 u-bolts P#(K1098) and (4)
5/16”-18 nylon flange locknuts P#(K2516) PER TUBE.
Refer to Figure 2-5. Note: Bottom of Tubes should rest
on the top edge of the Trailer Hitch Plate.

2-6 Upper Frame Assembly

Installation

Lift the upper frame assembly P#(A2047) into position,
and slide onto the lower mount tubes as shown in Figure
2-7 and secure with (2) 1/2” x 2-1/4” clevis pins
P#(K0133) and (2) hair pin clips P#(K0088).

Note:

It is

recommended that someone assist you when installing
the upper frame assembly.

2-5 Lower Mount Tube Installation

2-7 Top Assembly To Upper Frame

Assembly Installation

Assemble the hinge kit as shown in Figure 2-9, using (1)
Latch Plate P#(B0884), (1) 5/16”-18 x 1-1/4” HHCS
P#(K1156), (1) 5/16”-18 Ny-Flange locknut P#(K2516),
(3) 5/16” Flat Washers P#(K0042), (1) Latch Spacer
P#(S0006), (2) Extra Heavy 5/16” Fender Washers
P#(K0505) and (1) 5/16”-18 Lock Nut P#(K0506). Leave
the nuts loose enough to allow fluid movement of the top
when opening and closing. When opened, the top should
rest in the Latch Plate Slot.

Insert the Inlet P#(A2111) into the hole on the top
assembly from the inside and then snap the inlet into
place. The inlet should pivot freely about the hole.

2-8 Inlet Installation

2-9 Hinge Kit Assembly Installation

(2) 5/16”-18 x 2-1/2” HHCS

(2) 5/16”-18 Locknuts

Top Assembly

Figure 2-7

Nylon

Flange

Locknut

Hex
Bolt

Inlet

Hair Pin

Clip

Clevis

Pin

K0506

B0884

K2516

K0042

S0006

K0505

K0042

K1156

Figure 2-9

Figure 2-5

T

railer Hitch

Plate

Rubber

Dust Guard

10

«
...
8
9
10
11
12
...
»

Содержание Pro2B+ 21120902







































Отзывы:

Нет отзывов

Похожие инструкции для Pro2B+ 21120902

Бренд: D-Link Страницы: 2

Бренд: Samsung Страницы: 2

Бренд: Baroness Страницы: 19

Бренд: Baroness Страницы: 4

Бренд: Baroness Страницы: 5

Бренд: Baroness Страницы: 3

Бренд: Baroness Страницы: 142

Бренд: Baroness Страницы: 192

Бренд: Baroness Страницы: 60

Бренд: Quincy lab Страницы: 4

Бренд: Napoleon Страницы: 4

Бренд: hager Страницы: 4

Бренд: e-conolight Страницы: 3

Бренд: E+E Elektronik Страницы: 16

Бренд: E+E Elektronik Страницы: 14

Бренд: E+E Elektronik Страницы: 22

Бренд: E+E Elektronik Страницы: 16

Бренд: E+E Elektronik Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды