Cub Cadet LT 2138 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 60

Cub Cadet LT 2138 Скачать руководство пользователя страница 42

42

Figure 53

11. Pass the PTO belt downward, inside the tractor

frame, until the belt is below the two tractor front
lower pulleys. Twist the two sides of the PTO belt
1/4 turn inward to engage the narrow sides of the
belt into the grooves of the two tractor front-lower
pulleys (See Figure 54).

Figure 54

12. From the front of the tractor, push the PTO belt

through the front lift rod, then to the center of the
deck. Ensure that the forward end of the belt
remains positioned inside the front lower pulleys.

13. Install the rearward end of the PTO belt on the

upper pulley of the deck center double-pulley
(Refer to Figure 55). Ensure that the narrow side
of the belt engages the groove of the upper pulley.

Figure 55

14. While holding the belt in position, rotate and

engage the deck idler arm lever into its stop
bracket to provide tension on the PTO belt (See
Figure 56).

Figure 56

15. Connect the spark plug wire.

C. MAINTENANCE

CLEANING AND BLADE CARE

WARNING

Before performing any maintenance, place the
PTO switch in the “OFF” position, engage the
brake pedal lock, turn the ignition key to the
“OFF” position and remove the key from the
switch to avoid accidental starting and injury.

PTO

CLUTCH

PULLEY

PTO

BELT

TRACTOR FRONT
LOWER PULLEYS

PTO BELT

FRONT LIFT

ROD/BRACKET

ASSEMBLY

MOWER DECK
CENTER DOUBLE
PULLEY

PTO BELT

FRONT OF DECK

IDLER ARM

LEVER

LEVER STOP

BRACKET

«
...
40
41
42
43
44
...
»

Содержание LT 2138





























































Отзывы:

Нет отзывов