background image

2

hot. Never operate the unit without the fuel cap securely in place.
Loosen the fuel tank cap slowly to relieve any pressure in the tank.

• Add fuel in a clean, well-ventilated outdoor area where there are no

sparks or flames. Slowly remove the fuel cap only after stop-ping
engine. Do not smoke while adding fuel. Wipe up any spilled fuel
from the unit immediately. Always wipe unit dry before using.

• Move the unit at least 30 feet (9.1 m) from the fueling source and

site before starting the engine. Do not smoke or allow sparks and
open flames near the area while adding fuel or operating the unit.

WHILE OPERATING

• Never start or run the unit inside a closed room or building.

Breathing exhaust fumes can be fatal. Operate this unit only in a
well-ventilated outdoor area.

• Wear safety glasses or goggles that meet ANSI Z87.1 standards

and are marked as such. Wear ear/hearing protection when
operating this unit. Wear a face or dust mask if the operation is
dusty.

• Wear heavy long pants, boots, gloves and a long sleeve shirt. Do

not wear loose clothing, jewelry, short pants, sandals or go
barefoot. Secure hair above shoulder level.

• The cutting attachment shield must always be in place while

operating the unit as a trimmer. Do not operate unit without both
trimming lines extended, and the proper line installed. Do not
extend the trimming line beyond the length of the shield.

• This unit does not have a clutch. The cutting attachment continues

rotating when the engine is idling. If it does not, have the unit
adjusted by an authorized service technician.

• Adjust the handle to your size in order to provide the best grip.
• Be sure the cutting attachment is not in contact with anything

before starting the unit.

• Use the unit only in daylight or good artificial light.
• Avoid accidental starting. Be in the starting position whenever

pulling the starter rope. The operator and unit must be in a stable
position while starting. Refer to Starting/Stopping Instructions.

• Use the right tool. Only use this tool for its intended purpose.
• Do not overreach. Always keep proper footing and balance.
• Always hold the unit with both hands when operating. Keep a firm

grip on both handles or grips.

• Keep hands, face, and feet at a distance from all moving parts. Do

READ ALL INSTRUCTIONS BEFORE OPERATING

• Read the instructions carefully. Be familiar with the controls and

proper use of the unit.

• Do not operate this unit when tired, ill, or under the influence of

alcohol, drugs, or medication.

• Children and teens under the age of 15 must not use the unit,

except for teens guided by an adult.

• All guards and safety attachments must be installed properly

before operating the unit.

• Inspect the unit before use. Replace damaged parts. Check for fuel

leaks. Make sure all fasteners are in place and secure. Replace
parts that are cracked, chipped, or damaged in any way. Do not
operate the unit with loose or damaged parts.

• Carefully inspect the area before starting the unit. Remove all

debris and hard or sharp objects such as glass, wire, etc.

• Clear the area of children, bystanders, and pets. At a minimum,

keep all children, bystanders, and pets outside a 50 feet (15 m.)
radius; there still may be a risk to bystanders from thrown objects.
Bystanders should be encouraged to wear eye protection. If you
are approached, stop the unit immediately.

SAFETY WARNINGS FOR GAS UNITS

• Store fuel only in containers specifically designed and approved for

the storage of such materials.

• Avoid creating a source of ignition for spilled fuel. Do not start the

engine until fuel vapors dissipate.

• Always stop the engine and allow it to cool before filling the fuel tank.

Never remove the cap of the fuel tank, or add fuel, when the engine is

• IMPORTANT SAFETY INSTRUCTIONS •

RULES FOR SAFE OPERATION

Read the Operator’s Manual and follow all warnings and safety instructions. Failure to do so can result in serious injury to the

operator and/or bystanders.

FOR QUESTIONS, CALL 1-877-282-8684 IN U.S. OR 1-800-668-1238 in CANADA

The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and their explanations, deserve your careful
attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not
substitutes for proper accident prevention measures.

NOTE:

Advises you of information or instructions vital to the
operation or maintenance of the equipment.

SAFETY ALERT:

Indicates danger, warning or

caution. Attention is required in order to avoid serious
personal injury. May be used in conjunction with other
symbols or pictographs.

DANGER:

Failure to obey a safety warning will result

in serious injury to yourself or to others. Always follow
the safety precautions to reduce the risk of fire, electric
shock and personal injury.

WARNING:

Failure to obey a safety warning can

result in injury to yourself and others. Always follow the
safety precautions to reduce the risk of fire, electric
shock and personal injury.

CAUTION:

Failure to obey a safety warning may result

in property damage or personal injury to yourself or to
others. Always follow the safety precautions to reduce
the risk of fire, electric shock and personal injury.

SYMBOL

MEANING

SPARK ARRESTOR NOTE
NOTE: For users on U.S. Forest Land and in the states of
California, Maine, Oregon and Washington.

All U.S. Forest Land

and the state of California (Public Resources Codes 4442 and 4443),
Oregon and Washington require, by law that certain internal
combustion engines operated on forest brush and/or grass-covered
areas be equipped with a spark arrestor, maintained in effective
working order, or the engine be constructed, equipped and maintained
for the prevention of fire. Check with your state or local authorities for
regulations pertaining to these requirements. Failure to follow these
requirements could subject you to liability or a fine. 

This unit is

factory equipped with a spark arrestor.

If it requires replacement,

ask your LOCAL SERVICE DEALER to install the 

Accessory Part

#753-05900 Muffler Assembly

.

CALIFORNIA PROPOSITION 65 WARNING

WARNING

THE ENGINE EXHAUST FROM THIS PRODUCT CONTAINS

CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO

CAUSE CANCER, BIRTH DEFECTS OR OTHER

REPRODUCTIVE HARM.

WARNING:

When using the unit, you must follow the

safety rules. Please read these instructions before
operating the unit in order to ensure the safety of the
operator and any bystanders. Please keep these
instructions for later use.

WARNING:

Gasoline is highly flammable, and its

vapors can explode if ignited. Take the following
precautions:

Содержание HB425





























Отзывы: