Cub Cadet GT2523 Скачать руководство пользователя | Manualshive

Страница: 37 / 60

background image

37

4.

Remove the rearward end of the PTO belt from the
upper pulley of the deck center double-pulley
(Refer to Figure 43). Engage the deck idler arm
lever back into its stop bracket (See Figure 44).

Figure 43

Figure 44

WARNING

If the engine has been recently operated, the
exhaust system, engine, and surrounding areas
will be hot. To avoid personal injury, allow these
areas to cool before proceeding with the
following PTO belt removal instructions.

5.

Open the tractor hood and remove the forward end
of the PTO belt from the PTO clutch pulley on the
front of the engine (Refer to Figure 45).

Figure 45

6.

Pass the PTO belt downward, inside the tractor
frame, until the belt is below the two tractor front
lower pulleys and pull the belt clear of the tractor
(Refer to Figure 46).

Figure 46

7.

Pull the deck support pins outward, turn
downward and release so both spring-loaded
pins are held in the disengaged position against
the outer surface of the deck brackets (Refer to
Figure 47).

MOWER DECK

CENTER DOUBLE

PULLEY

PTO BELT

FRONT OF DECK

IDLER ARM

LEVER

STOP BRACKET

PTO

CLUTCH

PULLEY

PTO

BELT

PTO

CLUTCH

PULLEY

PTO

BELT

«
...
35
36
37
38
39
...
»

Содержание GT2523





























































Отзывы:

Нет отзывов

Похожие инструкции для GT2523

WEEKEND WARRIOR 6042

Бренд: Maschio Страницы: 46

PROXIMA PLUS 2011 Series

Бренд: Zetor Страницы: 204

Бренд: Curtis Страницы: 10

Бренд: DongFeng Страницы: 251

Бренд: MTD Страницы: 2

Бренд: New Holland Страницы: 41

Бренд: Winton Страницы: 12

Бренд: Agrison Страницы: 91

Бренд: Cadet Страницы: 88

BH Generation 4

Бренд: Valtra Страницы: 21

Бренд: WALTERSCHEID Страницы: 16

Бренд: Stanley Страницы: 32

Бренд: Still Страницы: 324

Бренд: Montgomery Ward Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды