manualshive.com logo in svg

Cub Cadet GT 3100, Руководство оператора

Поделиться
Скачать
Cub Cadet GT 3100 Скачать руководство пользователя страница 15

15

L. Transmission Oil Fill/Dipstick

The transmission oil fill/dipstick is
located at the back of the tractor in the
rear draw bar. The handle of the
transmission oil  dipstick  serves as
the fill tube plug and should fit snugly
in the fill tube.

M. Fuel Fill Cap

The fuel fill cap is located on the
fender to the left of the seat.

N. Cup Holder

The cup holder is located on the
fender to the left of the seat.

O. Hydraulic Lift Lever

The hydraulic lift lever is located on
the fender to the left of the seat. This
lever is used to operate the tractor’s
center lift system.

P. Center Lift Height Indicator

The center lift height indicator is
located in the left running board. This
indicator shows the operator the
relative height position of the hydraulic
center lift system. The lower number
indicates a lower setting.

Q. Deck Height Adjustment Knob

The deck height adjustment knob is
located on the left running board (See
Figure 10). Use this knob to set and
hold your desired downstop position
for the mower deck. 

Figure 10  

Each full rotation of the adjustment
knob equals approximately a 1/4 inch
adjustment in the deck height setting,
and there are four detent positions per
rotation.

Always use the tractor lift system to
raise the deck before turning the
adjustment knob.

R. Cruise Control Lever

Figure 11  

The cruise control lever is located to
the left of the steering wheel. Push the
cruise control lever downward while
traveling at the desired forward speed
to engage the cruise control.

S. Throttle Lever

The throttle lever is located to the left of
the steering wheel in the throttle/choke
lever pod. When set in a given position,
the throttle lever  will maintain a uniform
engine speed. Push the lever forward to
increase the engine speed. 

IMPORTANT: 

When using power

take-off operated equipment, best
performance is achieved with the
throttle lever in the “FAST” position.

T. Choke Lever

The choke lever is located to the left of
the steering wheel in the throttle/choke
lever pod. Push the lever forward to
close  the engine choke plate.

RAISE

LOWER

Height
Adjustment
Knob

This symbol shows the fast

This symbol shows the slow

position.

position

Содержание GT 3100

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды