Cub Cadet CC924 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 20

Cub Cadet CC924 Скачать руководство пользователя страница 10

10

3. Install the blade holder and blade holder

cover one by one.
4. Finally, install the locking nut and tighten

it by the hex wrench.

INSTALL THE CUTTING BLADE(if attached)
1. Align the shaft bushing hole with the locking

rod slot in the protective cover and the notch

in the gear case, and then insert the locking

rod into these three holes/slots. Holding the

locking rod to ensure the output shaft in

place.

2. Install the blade to the output shaft and

make sure it contacts closely with the shaft

busing.

Blade Holder Cover

Shaft Bushing

Locking Nut

Blade Holder

Blade Holder Cover

Wrench

Clockwise

Locking Rod

Gear case

INSTALL THE TRIMMER HEAD

1. Align the shaft bushing hole with the locking

rod slot in the protective cover and the

notch in the gear case, and then insert the

locking rod into these three holes/slots.

Holding the locking rod to ensure the output

shaft in place.
2. Ensure the threads of the trimmer head and

the center of the output shaft are in line

with each other, and then rotate the trimmer

head clockwise (observed by operator) until

it is securely

tightened.

Output Shaft

Protective Cover

Locking Rod

Gear case

Clockwise

«
...
8
9
10
11
12
...
»

Содержание CC924





















Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды