Cub Cadet 59A40051727 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 20

Cub Cadet 59A40051727 Скачать руководство пользователя страница 13

13

Auger Shaft

At least once a season, remove the shear pins and cotter pins on
the auger shaft. Oil or spray lubricant inside and on the plastic
bearings on the shaft, near the holes where the shear bolts were
removed before reattaching them and grease the fitting on the
auger gear assembly. See Figure 15.

Roller Chain

The roller chain transfers power from the stub shaft to the auger
gear assembly and should be lubricated at least once a season.
To Lubricate the chain:

Remove the hex nuts that secure the chain cover. See Figure

1.

16.

Lubricate the chain with Cub Cadet Chain Lube.

2.

Replace the cover and secure with the previously removed

3.

hex nuts.

section 8: Maintenance

Maintenance

Warning! before lubricating, repairing,

or inspecting, place tractor on a firm and

level surface. place the pto in the disen-

gaged (off) position, set the parking

brake, shut engine off, and remove key to

prevent unintended starting.

Chute Directional Control

The base of the discharge chute should be lubed with lithium
grease or WD-40® once a season. See Figure 14. Spraying the
inside of the chute with lubricant is also recommended.

PTO Lubrication

Lubricate all pivot points on the drive shaft, stub shaft and blower
drive shaft.

Spacers

Grease Fitting

Shear Pins

Cotter Pins

figure 14

Lube Chute Base

figure 15

Roller Chain

Hex Nuts

figure 16

«
...
11
12
13
14
15
...
»

Содержание 59A40051727





















Отзывы:

Нет отзывов