Cub Cadet 53TIHKTY050, Руководство оператора

Страница: 10 / 32

10 S
ection
2 — A
SSembly
& S
et
-U
p
7. Remove the seat tilt knob assembly from
the bag and install as shown in Figure 2-12.
(h)
(c)
(d)
(b)
(f)
(a)
(g)
(e)
Figure 2-12
Note:
Be sure to orient the recliner plate
(a) and install the plastic washer (b), spring
washer (c) and metal washer (d) as shown
in Figure 2-12. The plastic washer is on
the inside.
8. Slide the recliner bearing plate (a) onto the
recliner pin (e). Refer to Figure 2-12.
9. Then align the spiral (a) on the inside of the
recliner knob with the recliner pin. Make
sure the hub on the back of the recliner sits
properly into the large holes of the side
plate. See Figure 2-13.
(a)
Figure 2-13
10. Use a wrench to hand tighten the hex screw
(g) until the recliner knob (f) is difficult to
turn. Refer to Figure 2-12.
Note: Do not use power tools to install.
11. Gradually loosen the hex screw (g) until the
recliner knob moves freely. Do not loosen
the hex screw (g) more than one full turn.
12. Securely install the 1/4” nut onto the clinch-
stud (h) and rotate the recliner knob to
check the operation of the seat.
Seat Adjustment
Proper steering column and seat adjustment will
result in the following (to adjust the seat see below):
In the neutral position with hands on the steering
wheel,
•
Operator’s upper arms should be relaxed
and approximately vertical.
• Operator’s forearms should be
approximately horizontal.
• Operator’s back should stay in contact with
the seat back.
• Steering column should not contact
operator’s legs.
Check the results of any adjustments to the
conditions described above. Repeat any
adjustment procedures as required until all
conditions are met.
This machine is equipped with an adjustable seat,
which includes a retractable seat belt assembly and
an Operator Presence Sensor (OPS). The OPS, in the
form of a switch, is integrated into the seat bottom
and is connected to the machine electrical system.
The OPS must be connected to the electrical
wiring harness.
The seat can be adjusted forward and backward,
the armrests can be adjusted up and down (700
and 900 series), the mechanical suspension
mechanism weight/ride adjustment controls
can be adjusted for weights between 125- and
275-pounds (500 and 700 series) or air ride
adjustment (900 series), a lumbar support
can be adjusted and the seat can tilt forward
and backward.
Note: The seat base must be secured by the latch,
otherwise, the seat assembly could tilt forward.
To move the seat forward or back, locate the seat
adjustment rod under the seat. Push the rod (a)
to the left, slide the seat forward or back into the
desired position and release the rod (a) when the
seat is in the desired position. See Figure 2-14.
(a)
Figure 2-14
The seat tilt is controlled by the knob on the left
of the seat. Turn the knob rearward to tilt the
seat back, turn the knob forward to tilt the seat
forward. See Figure 2-15.
Figure 2-15
The mechanical suspension mechanism (500 and
700 series) incorporates weight/ride adjustment
controls for operators in the 125 to 275 lb. weight
range. Turn the knob on the front of the seat
clockwise to increase the weight capacity and
counter-clockwise to decrease. See Figure 2-16.
Figure 2-16
To vary the lumbar support (700 and 900 series)
move the lever on the right of the seat up and
down. See Figure 2-17.
Figure 2-17
To adjust the height of the arm rests (700 and 900
series), lift the arm rest and rotate the knob under
the arm rest right or left to increase or decrease the
height. See Figure 2-18.
Figure 2-18