Cub Cadet 521E Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 20

Cub Cadet 521E Скачать руководство пользователя страница 7

7

SECTION 3: KNOW YOUR SNOW THROWER

Be familiar with all the controls and their proper operation. Know how to stop the machine and disengage
them quickly.

Figure 9

•

Compare Figure 9 with the controls on your snow
thrower before starting the machine or trying to
operate it.

Choke Lever

Place choke lever in “ON” position to start a cold
engine.

Primer Button

Used to inject fuel directly into the carburetor to insure
fast starts in cold weather. Follow engine manual to
prime engine.

Ignition Key

Used to start engine. Put key in “ON” position to start.

Starter Handle

Used to manually start the engine.

Electric Starter

Used to start engine with a 120V power source.

Plug for Electric Start

Requires use of a two-prong outdoor electric cord

and a 120V power source.

Spark Plug Cover

Spark plug located under the cover.

Auger Control Handle

Located on the upper handle, the auger control handle
is used to engage and disengage the augers. The snow
thrower is designed to be propelled by the rotation of
the augers. Pull the control handle back against the
upper handle to engage the augers; release to
disengage.

Chute Crank

Located on right side of dash panel, the chute crank
determines the direction that snow will be discharged.
Turn clockwise to discharge snow to the left; turn
counterclockwise to discharge to the right.

Discharge Chute

The angle of the discharge chute controls the distance
that the snow is thrown. Tilt the discharge chute up for
greater distance; tilt down for less distance. Loosen the
hand knob on the side of the discharge chute to adjust.
Tilt the chute to the desired position, and tighten the
knob.

Stopping Engine

•

Turn ignition key to OFF position and remove it
from the snow thrower.

Upper

Auger Control

Chute Crank

Auger

Discharge

Shave
Plate

Handle

Electric Cord

Chute

Handle

Ignition

Key

Choke Lever

On

Off

Starter
Handle

Spark

Plug

Cover

Button

Primer

Electric
Starter

Plug for
Electric
Cord

«
...
5
6
7
8
9
...
»

Содержание 521E





















Отзывы:

Нет отзывов