Cub Cadet 450 Series Скачать руководство пользователя страница 12

12

The dirt washes off the tines easier if rinsed off im-
mediately instead of after it dries. Always towel dry the 
tiller afterwards and apply a light coat of oil or silicone to 
prevent rusting or water damage.

IMPORTANT: 

 Never use a “pressure washer” to clean 

your tiller. Water can penetrate tight areas of the tiller and 
its chain case and cause serious damage to the unit.

Belt Replacement

Your tiller has been engineered with a belt made of special 
material (Kevlar Tensile) for longer life and better perfor-
mance. It should not be replaced with an off-the-shelf belt. 
Order all belts through you authorized service dealer.
•  Disconnect and ground the spark plug wire against the 

engine.

•  Remove the belt cover from the left side of the tiller by 

remove two torx screws from the top of belt cover. See 
Figure 8.

•  Remove the hex cap nut and flat washer from the side 

of the belt cover and remove the self tap screw at the 
bottom of the front of the cover. 

•  Remove the belt keeper bracket located behind the 

engine pulley by removing two hex bolts and lock 
washers. See Figure 9.

•  Remove belt and reassemble new belt. Follow instruc-

tions in reverse order.

NOTE:  

Upon reassembly, make certain the belt is routed 

over the idler pulley and inside of belt keepers by engine 
pulley. See Figure 9.

WARNING:  Disconnect the spark plug 
wire and ground it against the engine 
before performing any repairs.

Engine

Refer to the separate engine manual for engine 
maintenance instructions.
Maintain 

engine oil 

as instructed in the separate 

engine manual packed with your unit. Read and follow 
instructions carefully.
Service 

air cleaner 

every ten hours under normal 

conditions. Clean every hour under extremely dusty 
conditions. Poor engine performance and flooding 
usually indicates that the air cleaner should be serviced. 
To service the air cleaner, refer to the separate engine 
manual packed with your unit.

IMPORTANT: 

Never run your engine without air cleaner 

completely assembled.
The 

spark plug 

should be cleaned and the gap 

reset every 25 hours of engine operation. Spark plug 
replacement is recommended at the start of each tiller 
season; check engine manual for correct plug type and 
gap specification.

Clean the engine 

regularly with a cloth or brush. Keep 

the cooling system (blower housing area) clean to 
permit proper air circulation which is essential to engine 
performance and life. Be certain to remove all dirt and 
combustible debris from muffler area.

Lubrication

Transmission

The transmission is pre-lubricated and sealed at the 
factory. It requires no checking unless the transmission 
is disassembled. To fill with grease, lay the right half of 
the transmission on its side, add 22 ounces of Benalene 
920 grease, and assemble the left half to it. This grease 
can be obtained at your nearest authorized dealer by 
ordering part number 737-0300.

Clutch Handle

Lubricate the pivot point on the clutch handle and the 
cable at least once a season with light oil. The control 
must operate freely in both directions.

Pivot Points

Lubricate all pivot points and linkages at least once a 
season with light oil.

Tine Shafts

Remove tine assemblies and lubricate the tine shafts at 
least once a season.

Wheel Shafts

Remove wheel assemblies and lubricate the axle shafts 
at least once a season.

Cleaning Tine Area

Clean the underside of the tine shield after each use. 

7

Maintaining 

Your Tiller

WARNING

Disconnect the spark 
plug wire and ground 
it against the engine 
before performing 
any repairs or  
maintenance.

Torx Screws

Belt Cover

Hex Cap Nut & 

Flat Washer

Self Tap Screw

Figure 8

Содержание 450 Series





















Отзывы: