background image

3. 

Slide the shave plate out of the off-set slot at the bottom 

of the housing, and from between the skid shoes and side 

panels of the housing.

4. 

With the mounting holes facing toward the back of the 

unit, slide the new shave plate into position and secure 

with the fasteners previously removed and loosened.

Lubrication

Gear Shaft

The gear (hex) shaft should be lubricated at least once a season 

or after every twenty-five (25) hours of operation.

NOTE: 

Before tipping the unit on the front housing, run the fuel 

tank empty to avoid a fuel leak.

1. 

Carefully pivot the snow thrower up and forward so that it 

rests on the auger housing. 

2. 

Remove the frame cover from the underside of the snow 

thrower by removing the self-tapping screws which secure 

it. Refer to Figure 6-6.

3. 

Apply a light coating of engine oil (or 3-in-1 oil) to the hex 

shaft. See Fig. 6-2.

NOTE: 

When lubricating the hex shaft, be careful not to get any 

oil on the aluminum drive plate or the rubber friction wheel. 

Doing so will hinder the snow thrower’s drive system. Wipe off 

any excess or spilled oil.
4. 

At least once a season grease the wheel axle with Arctic 

grease, part number 737-0318. The grease fitting is located 

on the wheel axle tube behind the wheel axle support 
bracket.

Wheels

At least once a season, remove both wheels. Clean and coat the 

axles with a multipurpose automotive grease before reinstalling 

wheels.

Maintenance

WARNING! 

Before servicing, repairing, lubricating, 

or inspecting, disengage all controls and stop 

engine. Wait until all moving parts have come to a 

complete stop. Remove the ignition key, disconnect 

the spark plug wire and ground it against the engine 

to prevent unintended starting. Always wear safety 

glasses during operation or while performing any 

adjustments or repairs.

Engine

Refer to the Engine Operators Manual Maintenance  included 

with the snow thrower.

Shave Plate and Skid Shoes

The shave plate and skid shoes on the bottom of the snow 

thrower are subject to wear. They should be checked periodically 

and replaced when necessary.

NOTE: 

The skid shoes on this machine have two wear edges. When 

one side wears out, they can be rotated 180° to use the other edge. 

To Replace skid shoes:

1. 

Remove the six carriage bolts, hex nuts, and bell washers 

that secure the two skid shoes to the sides of the auger 

housing. Refer to Figure 6-1.

2. 

Position the new skid shoes and secure with the carriage 

bolts, bell washers, and hex nuts. Make certain the skid 

shoes are adjusted to be level. Refer to Fig. 6-1.

To replace shave plate:

1. 

Remove the hex nuts, bell washers, and carriage bolts that 

secure the shave plate to the bottom of the snow thrower 

housing.

2. 

Remove the rear most hex nut, bell washer, and carriage 

bolt securing the back of each skid shoe to the sides of the 

housing. Loosen the remaining hex nuts securing the skid 

shoes.

Figure 6-1

Figure 6-2

Hex Shaft

Rubber Friction 

Wheel

Wheel Axle 

Support Bracket

Aluminum 

Drive Plate

Maintenance & Adjustments

6

15

Содержание 2X 930 SWE





























Отзывы: