Cub Cadet 25HP Tank 53BH5D8X750 Скачать руководство пользователя страница 32

MANUFACTURER’S LIMITED WARRANTY - TURF EQUIPMENT

This warranty is specific to the product manual to which it is attached.

For a complete list of products and warranties contact your authorized Cub Cadet Commercial dealer.

Proper maintenance of the purchased Cub Cadet Commercial equipment is the owner’s responsibility.  

Follow the

instructions in your owner’s manual for correct lubricants and maintenance schedule. Your Cub Cadet Commercial dealer
carries a complete line of quality lubricants and filters for your equipment’s engine, transmission, chassis, and attach-
ments.

What is Covered By This Warranty?  

This limited warranty covers any defect in materials and/or workmanship in your

Cub Cadet Commercial equipment to the original owner for the following time periods: 
A) First (1

st

) Year of Original Ownership: 

Both

 

Parts

 found defective in materials and /or workmanship 

and

 the

associated 

Labor

 of the particular repair are covered under the terms of this limited warranty

B)  Second (2

nd

) and Third (3

rd

) Year of Original Ownership:  

Parts

 found defective in materials and /or workmanship are

covered under the terms of this limited warranty.  

 

Limited Battery Warranty:  90-day free battery replacement in the case of defects in materials and/or
workmanship, thereafter prorated for the period from the fourth (4th) through the twelfth (12

th

) month of

ownership. 

“No-Fault Warranty”:  Covers the “No-Fault” to owner replacement of damaged belts, tires, seats, and  grass bags
(cutting blades are not included) for a period of One (1) month or One-Hundred (100) hours, whichever comes
first.  

Limited Engine Warranty:  Parts and Labor for defects in materials and/or workmanship are covered for the first
two (2) years of original equipment ownership.  Refer to the Engine Manual for specific limitations and restric-
tions. 

Accordingly, Cub Cadet Commercial will replace or repair any part or parts without charge through your authorized Cub
Cadet Commercial dealer subject to the above time and coverage limitations. Upon completion of your purchase, the
Serial Number/s of the unit will be registered with the Cub Cadet. This will initiate and validate your limited warranty and
the applicable Warranty Period.

What is Not Covered By this Warranty? 

Cub Cadet Commercial does not warrant ( a ) routine maintenance items such

as lubricants, filters (oil, fuel, air and hydraulic), cleaning, tune-ups, brake or clutch inspections, adjustments made as part
of normal maintenance, blades, blade sharpening, equipment setup, and normal wear items; ( b ) incidental cost such as
transporting equipment to and from the dealer, telephone charges or renting product temporarily to replace a warranted
product; ( c ) damage caused by use of the equipment for purposes other than those for which it was designed; ( d )
damage caused by accident or Disasters such as fire, flood, wind and lighting: ( e ) damage caused by unauthorized
attachments, modifications, alterations, improper servicing or maintenance, improper storage; or ( f ) any other abuse or
misuse of the equipment.   

Exclusive Warranty. 

The foregoing warranty is exclusive and in lieu of all other warranties or remedies, whether written,

oral or implied. Any and all implied warranties of merchantability, fitness for particular purpose, course of delaying or
usage of trade are hereby expressly disclaimed and excluded

.  (Some states do not allow the exclusion or limitation

of incidental or consequential damages, so the above exclusion or limitation may not apply to you.)

Limitation of Remedies. 

Under no circumstances, except to the extent such exclusions are prohibited by applicable law,

shall Cub Cadet Commercial be liable for any loss or damage, direct or indirect, special, incidental or consequential
arising out of the use of or inability to use this equipment including but not limited to any claim for loss of profits, loss of
profits, loss of savings or revenue, loss of use of the equipment or any associated equipment, facilities or continued
service, downtime, the claims of costs of third parties including customers and injury  to property. Some states do not
allow limitations on how long an implied warranty lasts of the exclusion or limitation of incidental or consequential
damages, so the above limitations or exclusion may not apply to you. 

This warranty gives you specific legal rights,

and you may also have other rights that vary from state to state.

Future Changes

: Cub Cadet Commercial reserves the right to reserve, change or modify the construction and design of

its equipment or any component part or parts thereof without incurring the obligations to make such changes or modifica-
tions in present equipment.

How to Obtain Service: 

Contact the authorized Cub Cadet Commercial dealer at the point of original retail purchase to

obtain service or replacement parts.

Products purchased outside the USA are not covered by this warranty

Cub Cadet
P.O. Box 368023
Cleveland, Ohio 44136

Form No. 02000539

 

Rev. 05-0  01/25/2005

Содержание 25HP Tank 53BH5D8X750

































Отзывы: