background image

8

Attach the grass bags using the slots shown in 
Figure 5. Close the grasscatcher cover.

Attaching the Discharge Chute

Raise the deck to its highest position. 

On older models:

 Remove the clip, if already 

installed on the deck next to the discharge chute 
opening, by removing the lock nut, spring washer 
and hex bolt that secure it. See Figure 6A.

Figure 6

On older models: 

A grasscatcher pin (G in Figure 

1) and nut (H in Figure 1) have been supplied in the 
hardware pack. Attach these to the deck in place of 
the clip just removed. Follow Figure 6B for order of 
assembly. Make sure to secure the pin tightly.

Raise the chute deflector on the deck and hold it 
while you position the discharge chute over the 
chute opening.

Place the top rear edge of the discharge chute over 
the top rear edge of the chute opening. 

Push down on the discharge chute so that its front 
bottom edge rolls over the bottom of the deck; then 
slide the chute forward to the stop on the deck. See 
Figure 7.

NOTE: 

The retainer strap is fitted at position B on the

discharge chute. However, on older models of tractors,
you may have to change the position of the strap
depending on the location of the grasscatcher pin on
the deck. Remove the retainer strap from position B on
the discharge chute to position A or C corresponding to
the position of the grasscatcher pin at A, B or C on the
deck. See Figure 7.

Figure 7

Place the deck at its lowest position.

Lock the discharge chute in position by hooking the 
retainer strap over the grasscatcher pin on the 
deck. See Figure 7 for the pin position. 

Raise the deck back to its highest position.

Insert the curved end of chute tube into the hole in 
the grass bag cover. See Figure 8.

Figure 8

Place the lower end of the chute tube over the 
discharge chute so that the two notches on the 
chute tube fit into the two corresponding notches on 
the discharge chute. See Figure 9.

Figure 9

Secure by clipping the two retainer straps of the 
discharge chute to the pins on the chute tube. See 
Figure 9.

Hex  Bolt

Spring

Washer

Hex  Lock 

Cutting 
Deck

Clip

Nut

Grasscatcher 

Pin

Nut

Deck

A

B

Chute Deflector

Retainer Strap

C

A

B

C

A

B

Pin

Insert chute tube here

Chute 
Tube

Retainer 
Strap

Chute 
Tube

Notch

Содержание 190- 670-100, 190-678-100













Отзывы: