Cub Cadet 190-004 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 20

Cub Cadet 190-004 Скачать руководство пользователя страница 7

7

SECTION 3: TO THE OWNER

Model 190-004-100, 42-inch hydraulic tiller attachment is designed for use on Series 3000 Garden Tractors only. It
will NOT fit nor operate properly or safely on ANY other tractor. Using this tiller attachment requires the use of the
weight kit bracket 190-413-100, suitcase weights part number 190-390-100 (two weights are required and three are
recommended), and the three point hitch assembly, model 190-207-100. These parts are available through an
authorized Cub Cadet dealer.

The instructions in this manual are divided into sections. Carefully read all sections and study the illustrations to
ensure proper installation and usage of this attachment. Read and observe all WARNING and CAUTION
statements. They are included to provide for the protection of the equipment installer and user, and to ensure the
prolonged service life of the equipment.

References to LEFT and RIGHT indicate the left and right sides of the tractor and tiller attachment when facing
forward in the operator

’

s position. Reference to the FRONT indicates the grille end of the tractor and reference to

the REAR dictates the drawbar end where the tiller attaches.

SECTION 4: LOOSE PARTS

The tiller attachment is shipped with the following loose parts in the carton. Remove all the loose parts from the
carton before discarding it. See Figure 1 to identify the parts, noting that these parts may be referred to again in the
following sections of the manual.

Figure 1

SECTION 5: ASSEMBLING THE TILLER

Hydraulic Pump Assembly

The hydraulic pump assembly is shipped complete with
a drive shaft, mounting brackets, and the hardware that
is necessary to mount it to the tractor.

The two hydraulic hoses are packaged separately from
the hydraulic pump assembly and need to be attached
to the fittings on the hydraulic pump. Both hoses have
regular female fittings on the end that will attach to the
hydraulic pump. The opposite end of the hoses have a
right angle fitting on the large diameter hose and a
regular female fitting on the small diameter hose.

These hydraulic hoses will attach to male fittings on
both the hydraulic pump assembly and the tiller
assembly.

NOTE:

Before installing the hydraulic hoses, make

certain that the hose hooks are aligned on the hydraulic
hose sleeve as shown in Figure 2.

To connect the hydraulic hoses to the hydraulic pump
assembly:

•

Locate both male hydraulic fittings on the hydraulic
pump. Notice that the fittings are not the same
diameter.

Hydraulic Pump Assembly

Rear Tine Shield

(for use w/out roller)

Tiller Frame w/Roller

Hydraulic Hoses

«
...
5
6
7
8
9
...
»

Содержание 190-004





















Отзывы:

Нет отзывов