manualshive.com logo in svg

Cub Cadet 1333SWE Series, Руководство оператора, Страница: 21 / 28

Поделиться
Скачать
Cub Cadet 1333SWE Series Скачать руководство пользователя страница 21

21

Model 1333 SWE

Ref. 

No.

Part No.

Part Description

1.

05523

Support Bracket: Pivot

2.

618-0278

Bush Assembly

3.

618-0279

Dogg Assembly LH

4.

618-0280

Dogg Assembly RH

5.

618-0282B

Shift Assembly

6.

618-0296

Wheel Bearing Assembly

7.

684-0115

Support Bracket Assembly

8.

684-0116

Shift Arm Assembly

9.

684-0117

Shift Rod Assembly

10.

684-0118

Auger Actuator Bracket Assy.

11.

684-0119

Drive Actuator Bracket Assy.

12.

684-0120

Frame Assembly

13.

684-0122

Sprocket Assembly

14.

710-0195

Hex Screw1/4-28 x .625”

15.

710-0538

Hex Screw5/16-18 x .625”

16.

710-0599

TT Screw 1/4-20 x .5”

17.

710-0788

TT Screw 1/4-20 x 1”

18.

710-1652

TT Screw1/4-20 x .625”

19.

710-3001

Hex Screw 3/8-16 x .880”

20.

710-3008

Hex Screw 5/16-18 x .75”

21.

710-3103

Hex Screw 5/16-18 x 2”

22.

710-3180

Hex Screw 5/16-18 x 1.75”

23.

711-1191

Hex Shaft: Drive 

24.

711-1193

Actuator Shaft

25.

711-1194

Actuator Drive Shaft

26.

712-0116

Lock Nut

27.

712-0138

Hex Nut 1/4-28

28.

712-0221

Jam Lock Nut

29.

712-0429

Hex Lock Nut

30.

712-0798

Hex Nut 3/8-16

31.

712-3010

Hex Nut 5/16-18

32.

713-0284

Chain

33.

713-0286

Chain

34.

713-0413

Sprocket

35.

714-0101

Hairpin Clip

36.

714-0104

Hairpin Clip

37.

714-0115

Cotter Pin

38.

714-0388

Key

39.

715-0249

Roll Pin

40.

717-0302

Drive Plate

41.

732-0121

Extension Spring

42.

732-0209

Extension Spring

43.

736-0119

Lock Washer 5/16

44.

736-0158

Lock Washer 5/8

45.

736-0160

Flat Washer

46.

736-0163

Flat Washer

47.

736-0217

Lock Washer

48.

736-0242

Beleville Washer

49.

736-0275

Flat Washer

50.

736-0300

Flat Washer

51.

736-0329

Lock Washer

52.

736-0623

Flat Washer

53.

736-0639

Flat Washer

54.

737-0170

Lubricant

55.

737-3007

Grease

56.

738-0143

Shoulder Screw

57.

738-0279

Spindle: Drive Plate

58.

738-0924

Shoulder Screw 1/4-28 x .375”

59.

741-0163A

Bearing Housing Assembly

60.

741-0192

Flange Bearing

61.

741-0563

Ball Bearing

62.

741-1111

Hex Flange Bearing

63.

746-0949

Steer Cable

64.

746-0951

Idler Cable: Auger 

65.

747-0973

Clutch Rod: Drive

66.

750-0903

Split Spacer

67.

750-0997

Spacer

68.

750-1097

Split Spacer

69.

750-1196

Spacer

70.

756-0344

Drive Pulley

71.

756-0625

Roller Cable

72.

784-0377

Frame Support Bracket

73.

784-0379

Frame Cover: Upper

74.

784-0380

Frame Cover: Lower

75.

784-0384

Auger Cable Bracket

76.

784-5590

Bracket: Shift — Frame

77.

738-0975

Axle: Wheel

78.

714-0151A

Klik Pin

79.

734-1593

Wheel 

Ref. 

No.

Part No.

Part Description

Содержание 1333SWE Series





























Отзывы:

Нет отзывов