background image

10

NOTE: 

Make sure that longer end of the boot mount firmly

secures around the bolt head on the chute mounting bracket.
The other end of boot mount should be securely placed
between the chute mounting bracket and the flange of the
deck opening. See Figure 10 .

Figure 10

Insert the curved end of the chute tube into the opening in 
the grass bag cover. See Figure 11. Slide the chute tube 
further into the cover opening for ease of assembly in the 
next step.

Figure 11

NOTE: 

The chute extension has raised notches on one end,

and for identification purposes, locate these notches before
starting to assemble.

Insert the end of the chute extension, that does not have 
raised notches, into the chute tube. 

Slide the chute assembly down and insert the other end 
of the chute extension into the chute elbow aligning the 
raised notches on both parts. 

Pull each retainer strap to the corresponding retainer 
hook on the chute tube and attach.

NOTE: 

If the retainer hooks were not attached to the chute

tube before shipping, please attach it as follows.

Place the retainer hook in one of the two holes on the 
chute tube. See Figure 12 inset.

Insert a hex bolt from Group E of the hardware pack 
through the retainer hook and the chute tube at this hole. 
Secure with flange lock nut from the same hardware pack 
group. See Figure 12 inset.

Repeat with the other set of hardware from Group E at 
the other hole on the chute tube.

NOTE: 

These hardware pieces will only be included in the

hardware pack if the retainer hook is shipped unassembled.

Figure 12

Replacing Muffler Tailpipe

Some older model mowers may have a rear facing tailpipe. If 
your mower is equipped with this tailpipe, you will need to 
order a straight tailpipe 751-10027 to replace it. Do not 
attempt to use the grass catcher kit with the rear-facing
tailpipe.

Figure 13

Discharge 

Chute Deflector

Boot Mount

NOTE: 

Grass catcher has been left out of picture for clarity.

Chute

Insert end 
of chute tube
here

NOTE: 

Mower is not shown 

for clarity.

Retainer 
Hook

Hex Bolt

Flange Lock 

Nut

Chute

Tube

Chute
Elbow

Extension Tube

Chute Tube

Retainer Strap

Rear-Facing
Tailpipe

Содержание 590-852-150

















Отзывы: