Trademarks
CTS is a registered trademark of Connection Technology Systems
Inc. Contents subject to revision without prior notice.
All other trademarks remain the property of their owners.
Copyright Statement
Copyright
Connection Technology Systems Inc.
This publication may not be reproduced as a whole or in part, in
any way whatsoever unless prior consent has been obtained from
Connection Technology Systems Inc.
FCC Warning
WPS/MPS-2006 Series Ethernet Switches have been tested and
found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These standards are
designed to provide reasonable protection against harmful
interference when these devices are operated in a commercial
environment. These devices generate, use, and can radiate radio
frequency energy and may cause harmful interference to radio
communications unless installed in accordance with this User’s
Guide. Operation of these devices in a residential area is likely to
cause harmful interference which will make the user responsible
for the appropriate remedial action at his / her own expense.
CE Mark Warning
These are Class A products. In a domestic environment these
products may cause radio interference in which case the user will
need to consider adequate preventative methods.
1. Checklist
The package should contain the following items:
- WPS/MPS-2006 Ethernet Switch
- User
’s Guide
- Installation Guide
Please notify your sales representative immediately if any item is
missing or damaged.
As for power adapters, please refer to Section 7 for more detailed
information.
2. Overview
WPS/MPS-2006 Ethernet Switches support IEEE802.3at PoE
feature and are specifically designed to supply power to
PoE-enabled devices such as WiFi AP or surveillance cameras.
They are power supply equipments (PSE) that can transmit data
and supply power at the same time to the powered devices (PD).
The maximum cable distance that can reach the powered devices
from the switch is up to 100M, allowing your powered devices to be
installed in a place where power is not easily accessible.
Besides, WPS/MPS-2006 Series Ethernet Switches aim at
industrial applications that demand wide range of operating
temperature and require redundant power supplies to create a
reliable and stable networking environment in the event of power
failure. They can also be mounted on the wall or onto 35mm DIN
rail using DIN rail clip on the Switch. The installation and operation
procedures are simple and straightforward. Operation status can
be locally monitored through a set of diagnostic LED indicators
located on the front panel.
Major Features:
3. Network Installation
Please follow the steps described below and refer to Figure 1 and
2 to complete the network installation.
Attach fiber cable from the Switch to the fiber network.
Attach a UTP cable from the 10/100Base-TX network to the
RJ-45 port on the Switch.
Connect the power adapter to the Switch and the Power LED
will light up. The Link/ACT/Speed and F/O Link/ACT LEDs will
light up as soon as all the cable connections are satisfactory.
WPS-2006 MPS-2006
Figure 1. Network Installation for FX Models
WPS-2006 MPS-2006
Figure 2. Network Installation for WDM/SFP Models
4. Terminal Block
TB1 and TB2 Power Supply:
There are two pairs of contacts on
the terminal block connector for power redundancy purpose. You
can use both pairs of power supply for redundancy purpose or use
either one pair of power supply on the terminal block and AC
external power supply to create redundant setup. The redundant
power supply will take over seamlessly when one power source is
down to protect your device or network from the loss of power.
When you use only one power supply (no redundant power is
available), the LED Power/Port Status will flash in orange to alert
the user.
Figure 3. Terminal Block Front and Top View
Port Fault Alarm:
One pair of port fault connection on the
terminal block is used to connect alarm devices such as speakers
or LEDs to alert users when the F/O port link is disconnected.
- Auto-Negotiation in TP port
- Store and Forward Switching Mechanism
- Support Full/Half duplex mode operation
- Support MDI/MDIX Auto-Crossover
- Support Flow Control
- Support alarms for power and F/O port failure
- Support 2K MAC address table
- Support 80K bytes Memory Buffer
- Support wide range of operating temperature (-20
o
C~60
o
C)
- Support DIN Rail and Wall Mounting
- Support redundant AC and DC power supply
Use flat-head
screwdriver to
loosen and tighten
the screw.
Insert positive or
negative wire as
indicated.
