CTS IES-3006 Series Скачать руководство пользователя страница 3

Trademarks 

 
CTS is a registered trademark of Connection Technology Systems Inc.   
Contents are subject to revision without prior notice. 
All other trademarks remain the property of their respective owners. 

 

Copyright Statement 

 
Copyright 

 2014 Connection Technology Systems Inc. 

This  publication  may  not  be  reproduced  as  a  whole  or  in  part,  in  any  way  whatsoever  unless 
prior consent has been obtained from Connection Technology Systems Inc. 

 

FCC Warning 

 

This equipment has been tested and found to comply with the limits for a Class-A digital device, 
pursuant  to  Part  15  of  the  FCC  Rules.  These  limitations  are  designed  to  provide  reasonable 
protection  against  harmful  interference  in  a  residential  installation.  This  equipment  generates, 
uses and can radiate radio frequency energy and, if the equipment is not installed and used in 
accordance  with  the  instructions,  it  may  cause  harmful  interference  to  radio  communications. 
However, there is no guarantee that interference will not occur in a particular installation. If this 
equipment  does  cause  harmful  interference  to  radio  or  television  reception,  which  can  be 
determined  by  turning  the  equipment  off  and  on,  the  user  is  encouraged  to  try  to  correct  the 
interference by one or more of the following measures: 
 

 

Reorient or relocate the receiving antenna. 

       

 

Increase the separation between the equipment and receiver. 

       

 

Connect the equipment into an outlet on a circuit different from that to which the receiver 
is connected. 

       

 

Consult your local distributors or an experienced radio/TV technician for help. 

       

 

Shielded interface cables must be used in order to comply with emission limits. 

 
Changes or modifications to the equipment, which are not approved by the party responsible for 
compliance, could affect the user’s authority to operate the equipment. 
 
Copyright ©  2014 All Rights Reserved.   
 
Company  has  an  on-going  policy  of  upgrading  its  products  and  it  may  be  possible  that 
information in this document is not up-to-date. Please check with your local distributors for the 
latest information. No part of this document can be copied or reproduced in any form without 
written consent from the company. 
 
Trademarks: 
All trade names and trademarks are the properties of their respective companies.

   

 

Содержание IES-3006 Series

















Отзывы: