CTP Systems CTPhone 1900 Скачать руководство пользователя страница 58

Страница: 58 / 132

3-10

DOC00101-01

CTPhone 1900 System Hardware & Software Installation

Base Station Indicators

For information on Base Station LEDs, see the Diagnostics and Trouble-
shooting chapter.

“Mini” Base Station Installation

WARNING:

•

Do not remove the blank RJ-45 connector.

•

Do not install any other connector instead.

•

Do not open the plastic case

Figure 3-7. “Mini” Base Station Wiring Diagram

“Mini” Base Station Installation

Step

Procedure

Assemble an E1 cable with the following description:
Cable type: 4 wire, (24-26 AWG)
Number of sides: 2
•

Side one - “Mini” base station: One RJ-11 connector

•

Side two - PBX: Use same configuration as before, but
use only one cable

Connect side one connectors to the “Mini” base station.

Connect side two connectors to the PBX exits.

Confirm that all red LEDs are off and that the green LED is
on.

If the “Mini” base station is not operating, try switching con-
nectors on the PBX side.

“Mini” Base Station (MBS)

RJ11

RJ45

W iring Table:

R J11 (M B S)

P BX

1 Ring 1    RX - 1
2 Tip   1     RX - 2
3 No Connection
4 No Connection
5 Ring 2    TX - 1
6 Tip   2     TX - 2

Содержание CTPhone 1900





































































































































Результаты поиска

Содержание CTPhone 1900

Отзывы:

Похожие инструкции для CTPhone 1900

Бренды по названию

Популярные бренды

CTP Systems CTPhone 1900, Руководство по применению

Результаты поиска

Содержание CTPhone 1900

Отзывы:

Похожие инструкции для CTPhone 1900

Бренды по названию

Популярные бренды