background image

EN • 3

EN

CONGRATULATIONS

on the purchase of your new professional switch mode battery charger. 

This charger is included in a series of professional chargers from 

CTEK SWEDEN AB and represents the latest technology in battery 

charging. MXTS 40 is a charger with multiple adjustable parameters.

MANUAL

• 

ThE ChArgEr iS DESigNED for ChArg-

iNg oNly BATTEriES ACCorDiNg To ThE 

TEChNiCAl SpECifiCATioN. Do NoT uSE 

ThE ChArgEr for ANy oThEr purpoSE. 

AlWAyS folloW BATTEry MANufACTur-

ErS rECoMMENDATioNS.

• 

NEvEr Try To ChArgE NoN rEChArgE-

ABlE BATTEriES.

• 

ChECK ThE CABlES prior To uSE. ENSurE 

ThAT No CrACKS hAvE oCCurrED iN 

ThE CABlES or BEND proTECTioN. A 

ChArgEr WiTh DAMAgED CABlES MuST 

NoT BE uSED. A DAMAgED CABlE MuST 

BE rEplACED By AN origiNAl pArT Sup-

pliED By CTEK.

• 

NEvEr ChArgE A DAMAgED BATTEry.

• 

NEvEr ChArgE A frozEN BATTEry.

• 

NEvEr plACE ThE ChArgEr oN Top of 

ThE BATTEry WhEN ChArgiNg.

• 

AlWAyS proviDE for propEr vENTilA-

TioN DuriNg ChArgiNg.

• 

AvoiD CovEriNg ThE ChArgEr. 

• 

A BATTEry BEiNg ChArgED CoulD EMiT 

EXploSivE gASES. prEvENT SpArKS CloSE 

To ThE BATTEry. 

• 

All BATTEriES fAil SooNEr or lATEr. A 

BATTEry ThAT fAilS DuriNg ChArgiNg iS 

NorMAlly TAKEN CArE of By ThE ChArg-

SAFETY

ErS ADvANCED CoNTrol, BuT SoME 

rArE ErrorS iN ThE BATTEry CoulD STill 

EXiST. DoN’T lEAvE ANy BATTEry DuriNg 

ChArgiNg uNATTENDED for A loNgEr 

pErioD of TiME.

• 

ENSurE ThAT ThE CABliNg DoES NoT 

jAM or CoMES iNTo CoNTACT WiTh hoT 

SurfACES or ShArp EDgES.

• 

BATTEry ACiD iS CorroSivE. riNSE iMME-

DiATEly WiTh WATEr if ACiD CoMES iNTo 

CoNTACT WiTh SKiN or EyES, SEEK iMME-

DiATE MEDiCAl ADviCE.

• 

AlWAyS ChECK ThAT ThE ChArgEr hAS 

SWiTChED To STEp 7 BEforE lEAviNg ThE 

ChArgEr uNATTENDED AND CoNNECTED 

for loNg pErioDS. if ThE ChArgEr 

hAS NoT SWiTChED To STEp 7 WiThiN 

55 hourS, ThiS iS AN iNDiCATioN of 

AN Error. MANuAlly DiSCoNNECT ThE 

ChArgEr.

• 

BATTEriES CoNSuME WATEr DuriNg uSE 

AND ChArgiNg. for BATTEriES WhErE 

WATEr CAN BE ADDED, ThE WATEr lEvEl 

ShoulD BE ChECKED rEgulArly. if ThE 

WATEr lEvEl iS loW ADD DiSTillED WATEr.

• (IEC  7.12  Ed.5)

 ThiS AppliANCE iS NoT 

iNTENDED for uSE By pErSoNS (iNCluD-

iNg ChilDrEN) WiTh rEDuCED phySiCAl, 

SENSory or MENTAl CApABiliTiES, or 

lACK of EXpEriENCE AND KNoWlEDgE, 

uNlESS ThEy hAvE BEEN givEN SupEr-

viSioN or iNSTruCTioN CoNCErN-

iNg uSE of ThE AppliANCE By A pErSoN 

rESpoNSiBlE for ThEir SAfETy. ChilDrEN 

ShoulD BE SupErviSED To ENSurE ThAT 

ThEy Do NoT plAy WiTh ThE AppliANCE. 

(EN 7.12)

 ThiS AppliANCE CAN BE uSED By 

ChilDrEN AgED froM 8 yEArS AND ABovE 

AND pErSoNS WiTh rEDuCED phySiCAl, 

SENSory or MENTAl CApABiliTiES, or 

lACK of EXpEriENCE AND KNoWlEDgE if 

ThEy hAvE BEEN givEN SupErviSioN or 

iNSTruCTioN CoNCErNiNg uSE of ThE 

AppliANCE iN A SAfE WAy AND uNDEr-

STAND ThE hAzArDS iNvolvED. ChilDrEN 

ShAll NoT plAy WiTh ThE AppliANCE. 

ClEANiNg AND uSEr MAiNTENANCE 

ShAll NoT BE MADE By ChilDrEN WiTh-

ouT SupErviSioN.

• 

CoNNECTioN To ThE MAiNS Supply 

MuST BE iN ACCorDANCE WiTh ThE 

NATioNAl rEgulATioNS for ElECTriCAl 

iNSTAllATioNS. 

• 

ChArgErS WiTh grouNDED MAiNS 

plug MuST oNly BE CoNNECTED To A 

grouNDED SoCKlET ouTlET.

• 

DoN´T plACE A fAN-CoolED ChArgEr 

So ThAT DuST, DirT or SiMilAr CAN BE 

SuCKED iNTo ThE fAN.

• 

ChArgErS WiTh ip-ClASS loWEr ThAN 

ipX4 ArE DESigNED for iNDoor uSE. 

SEE TEChNiCAl SpECifiCATioN. Do NoT 

EXpoSE To rAiN or SNoW.

Содержание MXTS 40









Отзывы: