CTE B-LIFT 18 HV Скачать руководство пользователя

Страница: 37 / 144

Aerial work platform

B-LIFT 18 HV

COD. UM0287_GB | REV. 00 | ED: 09/18

Chapter 3

DESCRIPTION AND TECHNICAL DATA

3.3

Identiication and CE marking

Machine: Mobile elevating work platform (PLE)

Model: B-LIFT

Type: 18 HV

Year of construction: Riportato sulla targhetta CE

Manufacturer:

CTE S.p.a.
Via Caproni, 7 - Z.I. - 38068 ROVERETO (TRIENT) - Italien

Identiication plate: On board, riveted on the turret, there is the identiication plate reproduced

in the picture.

Punch marks:

The factory number on the identiication plate is also stamped on the turret.

The vehicle gives the manufacturer‘s chassis number.
Consult your vehicle owner‘s manual for the location.

FABBRICANTE/MANUFACTURER:

CTE S.p.A.

Via Caproni, 7 - 38068 Rovereto (TN) - ITALY

Tel +39 0464 485050 - Fax +39 0464 485099

PIATTAFORMA DI LAVORO MOBILE ELEVABILE / MOBILE ELEVATING WORK PLATFORM

MODELLO:
MODEL:

TIPO:
TYPE:

NUMERO DI FABBRICA
FABRICATION NUMBER

ANNO DI COSTRUZIONE
YEAR OF CONSTRUCTION

PORTATA MASSIMA

RATED LOAD:

MASSIMA ALTEZZA DAL SUOLO

AL PIANO CALPESTIO PIATTAFORMA

MAXIMUM HEIGHT FROM THE GROUND AT WORK PLATFORM FLOOR
SBRACCIO MASSIMO

PARAPETTO PIATTAFORMA

MAXIMUM OUTREACH

GUARD-RAILS WORK PLATFORM

SOLLECITAZIONE MANUALE MASSIMA CONSENTITA

MAXIMUM ALLOWABLE MANUAL FORCE

MASSIMA VELOCITA’ DEL VENTO CONSENTITA

m/s

MAXIMUM ALLOWABLE WIND SPEED
PRESSIONE MASSIMA IMPIANTO IDRAULICO

bar

MAXIMUM PRESSURE HYDRAULIC EQUIPMENT

MASSA A VUOTO COMPRESO VEICOLO

NON LOADED MASS WITH VEHICLE

INCLINAZIONE MASSIMA AMMISSIBILE DEL TELAIO:
MAXIMUM ALLOWABLE INCLINATION OF CHASSIS:

ALIMENTAZIONE ELETTRICA ESTERNA
EXTERNAL ELECTIC POWER

COMPRESO N. PERSONE

E kg ATTREZZATURA

INCLUDING N. PERSONS AND kg EQUIPMENT

CODE

Fig.

3.2

Содержание B-LIFT 18 HV

















































































































































Результаты поиска

Содержание B-LIFT 18 HV

Отзывы:

Похожие инструкции для B-LIFT 18 HV

Бренды по названию

Популярные бренды

CTE B-LIFT 18 HV, Инструкция по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание B-LIFT 18 HV

Отзывы:

Похожие инструкции для B-LIFT 18 HV

Бренды по названию

Популярные бренды