CST/BERGER 2 610 A15 290, Оригинальное руководство пользователя

Страница: 38 / 500

38 | English
2 609 141 178 • 2.4.14
– To change the volume level or switch off the audio signal,
push the acoustic signal button 34 until the requested vol-
ume level is indicated on the display. At low volume level, the
audio signal indicator
h appears on the display with one bar;
at high volume level, the indicator appears with three bars
(only available for the highest frequency). When the audio
signal is set to off, the indicator goes out. When pressing the
audio signal button, a short audio signal sounds first for con-
firmation, then a second short audio signal sounds in the se-
lected volume level.
Independent of the selected audio signal setting, a short beep
for confirmation sounds at low volume level and the set frequen-
cy each time a button is pressed on the measuring tool.
– To change the frequency , press and hold the audio signal
button 34 and briefly press the On/Off button 42 . A brief au-
dio signal in the selected frequency sounds each time for
confirmation.
The signal tone setting is maintained after switching the meas-
uring tool off and on again.
Working Advice
Strobe shield
TM
Protection
The measuring tool is equipped with an electronic filter for
bright sunlight. The filter prevents, e. g., interference from the
warning lights of construction machines. Effective operation of
the filter is possible only when sensor
37 is not obstructed and
clean.
Marking
When the laser beam runs through the centre of the reception
area
35 , its height can be marked at the centre mark 40 right
and left on the measuring tool. The centre mark is located
50,8 mm away from the top edge of the measuring tool.
When marking, take care to align the measuring tool exactly ver-
tical (for horizontal laser beam), or horizontal (for vertical laser
beam), as otherwise the marks are offset with respect to the la-
ser beam.
Attaching with the Holder (see figure C)
With the holder 48 , the measuring tool can be fastened to a “Cut
& fill” rod 50 (accessory) as well as to other auxiliary tools with
a width of up to 65 mm.
– Screw the holder 48 to the retainer opening 47 on the rear
side of the measuring tool with fastening screw 51 .
– Loosen locking screw 49 , slide the holder, e.g., onto the “Cut
& fill” rod 50 and tighten locking screw 49 again.
– The holder 48 can be horizontally aligned with help of the
spirit level 52 .
A measuring tool mounted out-of-level leads to faulty meas-
urements.
Maintenance and Service
Maintenance and Cleaning
– Keep the measuring tool clean at all times.
– When heavily contaminated, the measuring tool can be
cleaned under running water. Do not immerse the measuring
tool in water and do not subject it to a high-pressure water
jet.
– Wipe off debris using a moist and soft cloth. Do not use any
cleaning agents or solvents.
After-sales Service and Application Service
In all correspondence and spare parts orders, please always in-
clude the 10-digit article number given on the type plate of the
measuring tool.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0844) 7360109
E-Mail: boschservicecentre@bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: (01300) 307044
Fax: (01300) 307045
Inside New Zealand:
Phone: (0800) 543353
Fax: (0800) 428570
Outside AU and NZ:
Phone: +61 3 95415555
www.bosch.com.au
Republic of South Africa
Customer service
Hotline: (011) 6519600
OBJ_BUCH-1596-003.book Page 38 Wednesday, April 2, 2014 10:56 AM
www. .com
information@itm.com 1.800.561.8187