CSM SL560 GYRO Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 24

background image

12

Performing the Quick-setup

To access the Quick-setup you toggle the gain switch a couple of times
during the gyro boot-up time (this is the first few seconds after the radio
system is switched on). The gyro acknowledges this by zipping the servo
back and forth a couple of times before parking it in the mid position. The
gyro also samples the mid-stick pulse width at this time so you need to
have the rudder trim set to centre before entering the Quick-setup.

Make

sure you do not touch the rudder stick at this time.

For maximum

accuracy turn on the transmitter and allow a few seconds for it to settle
before turning on the receiver and starting the Quick-setup. If low gain
values (less than 35%) are set the gyro may not enter the Quick-setup.

Gyro sense reversing

The first item to be set is the gyro sense reversing. Check that the yellow
"REV" LED turns on and off as the rudder stick is moved fully left and
right. Now,

if the servo operating sense has been set correctly

a s

described previously,

simply push the rudder stick to the left and release

it back to the middle.

This will set the gyro sense to match your system.

The servo will travel over to allow the user to check that left tail command
is indeed being given and once this has been checked

the gyro sense is

'entered' by toggling the gain switch once

(i.e. into mode 0 and back to

mode 1) The gyro will 'zip' the servo back and forth in acknowledgement
and again park the servo in the middle.

Super servo support

Now set the Super Servo support. By pushing the stick left and right you
will observe the green "SUPER SERVO" LED turns on and off. Just select
super servo on or off as required (LED ON = SUPER SERVO ACTIVE).
Having done so, release the stick to the middle and enter the super servo
condition by toggling the gain switch. This will be acknowledged as before
by zipping the servo back and forth.

Servo travel limits

Following the acknowledgement the servo travels over to the first travel
limit and this can now be adjusted. Hold the stick over in the direction of
the servo deflection to increase the limit or hold it over against the
deflection to reduce the limit. The servo will move as you change the limit
and with its slow movement it is possible to set the limit very accurately.

«
...
10
11
12
13
14
...
»

Содержание SL560 GYRO

























Отзывы:

Нет отзывов

Похожие инструкции для SL560 GYRO

Бренд: laerdal Страницы: 8

Resusci Anne QCPR

Бренд: laerdal Страницы: 34

Бренд: 3B Страницы: 44

ISOLATE RNA Mini Kit

Бренд: Bioline Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды