CSI signature 2 hydroxr vs Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 24

CSI signature 2 hydroxr vs Скачать руководство пользователя страница 4

SIGNATURE 2 SERIES

-Installation Requirements-

HYDROXR™ VS Tank

• A level floor position between the well pump and filter tank. (After the pressure tank, if installed.)
• DO NOT install in an area of direct sunlight or where freezing temperatures may occur!

Peroxide Feed System

• Leave ample room near HYDROXR ™ VS Tank to accommodate the Peroxide Feed System.

Filter Tank

• A level floor position ahead of piping into water heater.
• Unit must be installed at least 10’ ahead of the inlet to a water heater to prevent damage due to back-up of hot water.
• DO NOT install unit in an area of direct sunlight or where freezing temperatures may occur!

Installation

4

Note : Caution should always be used in sizing filters! Always choose a unit by first satisfying the Backwash requirement.
Use of a flow control in the Service Line is highly recommended. Consult the factory or your field sales person with ques-
tions.

«
...
2
3
4
5
6
...
»

Содержание signature 2 hydroxr vs

























Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды