background image

Service Instruction Sheet

Introduction

These instructions are intended for use with comparator rebuild kit (

PN 

3143) and with the fine 

adjust kit (

PN 

3205). Rebuild kit 3143 contains all of the parts and tools required to rebuild the 

GaugeCal

XP

 pressure comparator, while kit 3205 contains the parts and tools required to install 

the optional fine adjust. Rebuilds and installation should be performed only by qualified personnel.

Service Instructions

1

  Remove all gauges from the 

GaugeCal

XP

 

pressure comparator.

2

  Remove any gauge or stem adapters from 

both the flange stem and gauge base. 

(figure 1)

.

3

  Tip the comparator on its end to completely 

drain the water, oil, or isopropyl alcohol from 
the system. Always dispose of fluids in a 
responsible manner.

4

  Use a 3mm Allen key to remove the two (2) 

cap screws securing the Reservoir to the 
Main Seal Block, then lift to remove the Res-
ervoir and Reservoir o-ring (

PN 

1959) 

(figure 2)

.

5

  Remove the press-fit Reservoir Vessel, and 

replace the lower seal o-ring (

PN 

3033) 

(figure 2)

.

6

  Use a 5mm Allen key to remove the Handle 

Assembly cap screw and washer, then pull to 
slide the Handle Assembly from the Piston 
Assembly 

(figure 3)

. Be sure to also remove 

the Key from the Piston Assembly Leadscrew 

(figure 3)

.

PRESSURE COMPARATOR

10000PSI–700bar

Gau

G

eCa

L

XP

Figure 1

Figure 2

Figure 3

C R Y S T A L

 

engineering corporation

Содержание GaugeCaLXP









Отзывы: