Crystal Vision Indigo ADP 310 Скачать руководство пользователя | Manualshive

Страница: 27 / 49

background image

Crystal Vision

Control Descriptions

AES Output Router

Route AES audio inputs to AES audio outputs. Mute output channels. This menu is only
available if DIOP4 piggybacks are fitted.

Audio Op
Channels

Display current selections (green circles) and pre-select the
cross point to be routed when the ‘Take’ button is pressed
(red circles). The AES inputs shown along the top of the
matrix will be routed to the AES output channels shown
down the left hand side. The screen grab above has an input
DIOP4 piggyback fitted in the front position (1-4 L & R) and
an output DIOP4 in the rear position (C9-C16). Clicking on the
intersection of the input and output will show a red circle
which will change to green when the ‘Take’ control is
selected. All cross points can be pre-selected. The screen
grab above shows inputs 1R-3R pre-selected to output DIOP4
channels C9-C13.

Present

On when audio inputs are present.

Mute

Mute the selected output channels.

Take

Switch all pre-selected cross points in one go.

ADP 310 User Manual R1.2

26

19 June 2019

«
...
25
26
27
28
29
...
»

Содержание Indigo ADP 310


















































Отзывы:

Нет отзывов

Похожие инструкции для Indigo ADP 310

Бренд: Paradyne Страницы: 112

Бренд: Garland Страницы: 6

Бренд: Opengear Страницы: 2

Бренд: Xilica Audio Design Страницы: 30

Бренд: HARTING Страницы: 13

Бренд: IBASE Technology Страницы: 71

Бренд: Net to Net Technologies Страницы: 4

Anybus Communicator ABC4021

Бренд: HMS Networks Страницы: 60

Бренд: ADS Technologies Страницы: 1

HiGain H2TU-R-402 List 7A

Бренд: ADC Страницы: 7

Бренд: Renesas Страницы: 28

EK-Loop Modulus Series

Бренд: ekwb Страницы: 7

Бренд: Uniden Страницы: 5

CNPS7000A Series

Бренд: ZALMAN Страницы: 9

Бренд: ICP DAS USA Страницы: 8

Бренд: Penguin Edge Страницы: 2

PCMCIA High Speed Serial Card CE 232HSPCC

Бренд: B&B Electronics Страницы: 14

Бренд: Datum Страницы: 49

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды