Crystal Vision DEC102S страница 25 Скачать руководство пользователя

Страница: 25 / 41

Crystal Vision

Card edge operation

DEC102SUser ManualV1.0 05/11/03

Setting video standard and decoder options

The four-lever switch to the left of the card edge matrix display is used to configure the
main options in conjunction with on-board jumper links:

•

10 bit or 8 bit processing

•

525, 625 or automatic line standard selection

•

Composite or Y/C decoder input

•

VBI blanking ON/OFF

Lever

DOWN

Lever 1

Automatic switching between 10 and 8
bit mode

10 or 8 bit mode selected manually using
jumper link J5

Lever 2

Automatic switching between 625 and
525 line standard

625 or 525 standard selected manually using
jumper link J3

Lever 3

Composite input

Y/C (S-video) input.

Lever 4

VBI data passed unprocessed on
luminance channel

VBI data blanked

Forcing the video standard

The video standard can be forced by using jumper link J3 in conjunction with lever 2 of
the four-lever switch on the card edge:

Link

Position

Function

Towards edge connector

Manually select video standard when piano switch 2 is DOWN
Link to the rear – forces 625 line standard
Link to the front – forces 525 line standard

The location of jumper links is shown in the module configuration section of the Installation chapter.

Note:

Vertical Blanking Interval data is normally present in PAL on lines 7-22 and 319-335
and in NTSC on lines 10-20 and 273-282.

Содержание DEC102S










































Результаты поиска

Содержание DEC102S

Отзывы:

Похожие инструкции для DEC102S

Бренды по названию

Популярные бренды

Crystal Vision DEC102S, Руководство пользователя

Результаты поиска

Содержание DEC102S

Отзывы:

Похожие инструкции для DEC102S

Бренды по названию

Популярные бренды