Crystal Mountain Mogul Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 15

Crystal Mountain Mogul Скачать руководство пользователя страница 1

5- 1

REMOVAL
1. Remove the locking pin located at rear of Crystal Guard (fig.1-1).

2. Place finger tips of both hands on the Crystal Guard (fig.2-1) and turn it counter clockwise until
it is free from the cooler (fig.2-2) opening and remove from the cooler (fig.2-3).

3. To reinstall reverse these steps.

Note: Remember to replace locking pin to secure Crystal Guard to cabinet.

INSTALLATION
If you take apart the Crystal Guard for sanitation or because a part of it needs replacing, reassem-
ble as below.
4. Ensure that the Crystal Pin has the O-Ring in place at its base firmly insert the Crystal Pin inside
the Crystal Guard (fig.4-1). Make sure that the Crystal Pin’s four locking tabs have completely pro-
truded through the locking tabs entries (fig.4-2).

Note: Ensure that the Crystal Pin has the O-Ring in place.

Removal and Installation

Notice:
The information and/or procedures presented in the following demonstration(s) should be performed by a trained Water Cool-
er Service Technician only.
Never attempt to service or repair a water cooler while it is plugged into any power supply.
Prior to any service or repair of the water cooler, ensure that the water has been completely drained from the system.

. Crystal Guard

Removal & Installation Procedure

figure 1-1

figure 2-1 figure 2-2 figure 2-3

figure 4-1 figure 4-2

1
2
3
...
»

Содержание Mogul
















Отзывы:

Нет отзывов