Crunch Ground Ponder GPV2400.4 Скачать руководство пользователя страница 6

GROUND POUNDER

DRIVE

GROUND POUNDER

DRIVE

+  - gnd  -  +

HI INPUT

5V  0.2V         0dB  12dB      60Hz  1.2KHz    30Hz  250Hz

 LEVEL

       BASS EQ        HPF             LPF

FULL

 LPF HPF    MONO       STEREO

X-OVER            MODE

LINE OUT

  LINE INPUT

L

L

R

R

POWER INPUT

SPEAKER OUTPUT

BRIDGED

-  LEFT   +             -   LEFT  +

FUSE

GND     REM    +12V

+  - gnd  -  +

HI INPUT

5V  0.2V         0dB  12dB      60Hz  1.2KHz    30Hz  250Hz

 LEVEL

       BASS EQ        HPF             LPF

FULL

 LPF HPF    MONO       STEREO

X-OVER            MODE

LINE OUT

  LINE INPUT

L

L

R

R

POWER INPUT

SPEAKER OUTPUT

BRIDGED

-  LEFT   +             -   LEFT  +

FUSE

GND     REM    +12V

GPV800.2 / GPV1100.2 / GPV3500.2 2-CHANNEL AMPLIFIER APPLICATIONS 

4

Stereo high pass with mono low-pass in a 2 way active, or bi-amplified system

Crossover frequency control checklist:

In this application we will use a 2 channel amplifier for the high frequencies, and a second 

Highs amplifier:

one for the low frequencies, or mono sub bass. Please consult the speaker specifications 

- HI PASS: 100 Hz

to determine maximum amplifier power requirements.

- LOW PASS: N/A

Interconnect cable checklist:

Connect the inputs of the HIGHS amplifier to a Radio/CD with good quality RCA cables. 

Lows amplifier:

Connect the LINE OUT of the HIGHS amplifier to the inputs of the BASS amplifier with a 

- HI PASS (Subsonic filter): 10 Hz to 40 Hz

stereo RCA to RCA cable.

- LOW PASS: 80 Hz

Mono bass woofer wiring:

Please note that these frequency points are suggestions only. Refer to the loudspeaker 

Connect the mono speaker positive terminal to the RIGHT +, and its negative terminal to 

manufacturer specifications and the section

 “Setting up systems after installation for best 

LEFT -.

performance”

Switch setting checklist:

Level control checklist:

- Highs amplifier:

  

X-OVER

 switch in the 

HPF

 position.

- Refer to the section 

“Setting up systems after installation for best performance”

                               

MODE

 switch in the 

STEREO

 position.

Minimum final loudspeaker impedances:

- Lows amplifier:

  

X-OVER

 switch in the 

LPF

 position.

- 2-Ohms per channel stereo.

                              

MODE

 switch in the 

MONO

 position.

- 4-Ohms mono bridged.

FULL RANGE

STEREO LINE INPUT

STEREO

INTERCONNECT

RCA CABLE

MONO BASS

SPEAKER

REMOTE TURN-ON

REMOTE TURN-ON

CHASSIS GROUND

CHASSIS GROUND

TO B 12 volts VIA FUSE

TO B 12 volts VIA FUSE

FULL RANGE

SPEAKERS

Содержание Ground Ponder GPV2400.4
















Отзывы: