Crunch CRB Series Скачать руководство пользователя страница 6

6

LED-ILLUMINATION

The CRUNCH CRB subwoofer enclosures have an integrated LED-illumination. This illumination 

is only allowed to light up, if the vehicle is not in driving condition. It is recommended to switch the 

illumination with the vehicle‘s trunk illumination. 

For the + 12V power supply of LED-illumination, use 

the attached cable at the right terminal and connect 

it accordingly. Please ensure the correct polarity as 

marked.

NOTE: 

Do not use the speaker cables as power supply 

for the LED-illumination.

POWER RATINGS

The CRUNCH CRB subwoofer enclosures are designed for high bass levels. Anyhow it is possible, 

that unsatisfying sound characteristics could be caused by too low or too high amplifier power. In 

certain circumstances this even can cause a damage to the loudspeakers.
It is recommended to choose rather a more powerful amplifier (ca. 15-20% more Watts RMS than 

the max. RMS power rating of the woofer) and to use the amplifier not at the maximum output level 

(low distortion factor, good sound characteristics). A weaker amplifier at the maximum level  causes 

worse sound characteristics due to the higher distortion factor.
Never crank up the output volume of your amplifier to the maximum level or run the amplifier into 

the clipping range. If the sound is distorted and not clean, turn back the level until the distortions 

disappear.
The CRUNCH CRB subwoofer enclosures have no integrated limiter or clipper, which is limiting the 

level upwards. Overamplified bass peaks leads inevitably to a burn out of the voice coil of the woof-

er. A burn out of the voice coil, caused by clipping/overamping is not covered by the usual warranty.

Recommended power ratings:

•  1 x stereo-amplifier with 2 x 175 - 600 Watts RMS (Sinus) into 4 Ohms
•  1 x mono-amplifier with 350 - 600 Watts RMS into 2 Ohms

Please refer to the minimum impedance of the installed amplifier. In case of doubt ask your special-

ist dealer. 

Please also refer to the interconnection examples on the next page.

ENGLISH

Содержание CRB Series









Отзывы: