background image

20

Crown amplifiers are quality units that rarely require
servicing.  Before returning your unit for servicing,
please contact Crown Technical Support to verify the
need for servicing.

This unit has very sophisticated circuitry which should
only be serviced by an authorized Crown Service Center..
This is one reason why each unit bears the following
label:

CAUTION: To prevent electric shock, do
not remove covers. No user serviceable
parts inside. Refer servicing to a
qualified technician.

Worldwide Service

Service may be obtained from an authorized service
center.  Contact your local Crown/Amcron distributor or
our office for a list of authorized service centers.  To
obtain service, simply present the receipt as proof of
purchase along with the defective unit to an authorized
s distributor. They will handle the necessary paperwork
and repair.

Remember to transport your unit in the original factory
pack.

Service Shipping Instructions:

1. Contact your local Crown distributor for details

regarding where to send your amplifier.  This
information is available on the Crown website or by
contacting Crown Audio Customer Service, see
details panel.

2. To ensure the safe transportation of your unit to

the factory, ship it in an original factory packing
container. If you don’t have one, call or write
Crown’s Parts Department. With the exception of

Always use the
original factory pack
to transport the unit.

1 1 . 0

S e r v i c e   &   W a r r a n t y

Crown Audio Customer Service

Technical Support / Factory Service
Plant 2 SW, 1718 W. Mishawaka Rd., Elkhart,
Indiana 46517 U.S.A.

Telephone:

219-294-8200
800-342-6939 

(North America,

Puerto Rico, and Virgin Islands

only)

Facsimile:

219-294-8301 

(Technical Support)

219-294-8124 

(Factory Service)

Internet:

http://www.crownaudio.com

polyurethane or wooden crates, any other
packing material will not be sufficient to
withstand the stress of shipping. 

Do not use

loose, small size packing materials.

3. Do  not ship the unit in any kind of cabinet

(wood or metal). Ignoring this warning may
result in extensive damage to the unit and the
cabinet. Accessories are not needed—do not
send the product documentation, cables and
other hardware.

If you have any questions, please call or write the
Crown Technical Support Group.

Содержание Pulse 21100























Отзывы: