Crown CT36073, Оригинальное руководство пользователя

Страница: 22 / 140

22
English
Appliance components
1 Cylinder cover
2 Engine
3 Transportation handle
4 Receiver
5 Protection unit
6 Button of protection unit
7 Ventilation slots
8 Wheel *
9 Drain valve
10 Air filter (assembly)
11 Piping
12 On / off switch
13 Pressure relay (pressostat)
14 Pressure regulator
15
Removable transportation handle
16
Safety valve
17
Outlet fitting
18
Manometer of regulated pressure
19 Receiver manometer
20 Check valve (assembly)
21 Rubber mount *
22 Nut for installing rubber mount *
23 Washer for installing rubber mount *
24 Bolt for installing rubber mount *
25 Wheel installing washer *
26 Wheel installing spring washer *
27 Wheel installing nut *
28 Wheel installing stud *
29 Wing screw *
30 Fitting *
31 Hose clamp *
32 Hose *
33 Quick-change fitting *
34 Quick-change adapter *
35 Air filter housing
36 Filter element *
37 Air filter cover
38 Check valve housing
39 Piston
40 Spring
41 Screw plug
* Optional extra
Not all of the accessories illustrated or described
are included as standard delivery.
Installation and regulation of appliance
elements
Before any procedures, be sure to switch off the
appliance, remove the current-carrying cable from
the socket and discharge pressure in receiver 4
(pulling by the ring of safety valve 16 or opening
the valve onto outlet fitting 17 (in case when
nothing is connected to the fitting 17)).
Do not draw up the fastening elements
too tight to avoid damaging the thread.
Mounting / dismounting / setting-up of
some elements is the same for all appli-
ance models, in this case specific mod-
els are not indicated in the illustration.
For improve understanding of drawings,
some structural elements of appliances
are not shown onto drawing.
Rubber mounts assembly / disassembly (see fig. 1)
[CT36075, CT36076]
• Install the rubber mounts
21
as shown in fig. 1.
• Disassemble in the reverse sequence�
Wheels assembly / disassembly (see fig. 2)
[CT36075, CT36076]
• Install wheels 8 as shown in fig. 2.
• Disassemble in the reverse sequence�
Removable transportation handle assembly / disas-
sembly (see fig. 3)
[CT36076]
• Install the removable transportation handle 15 as
shown in fig. 3.
• Disassemble in the reverse sequence�
Connecting / disconnecting the air hose
Using thread fittings (see fig. 4)
• Attach hose clamp 31 to the end of hose 32 (see
fig. 4.1).
• Install fitting 30 into hose 32 �
• Tighten the screw of hose clamp 31 �
• When connecting, screw fitting
30
on outlet fitting
17
(see fig. 4.2).
• When disconnecting unscrew fitting 30 �
Using quick-change fittings (see fig. 5-6)
• Attach hose clamp 31 to the end of hose 32 (see
fig. 5.1).
• Install quick-change fitting 33 into hose 32 �
• Tighten the screw of hose clamp 31 �
• Install quick-change adapter
34
on outlet fitting
17
(see fig. 5.2).
• When connecting, insert (until it clicks) quick-change
fitting 33 into quick-change adapter 34 (see fig. 6.1).
• When disconnecting, move the bush of the quick-
change adapter 34 , as shown in fig. 6.2, and remove
quick-change fitting 33 �
Initial operating of the appliance
• Make sure the voltage matches technical
specifications printed on the appliance.
• Check power cable and extension cord condition; if
any damage is detected, the cable shall be replaced�
•
Check the condition of the air hose; if damaged,
replace it�
Switching the appliance on / off
[CT36073]
Before connecting the appliance to the mains,
make sure that on / off switch 12 is in "OFF"
position (see fig. 7.2).