14
X
-15P-T
Installation Instructions
15123197-A
2
15123197-A
3
Cleaning Instructions
Rinse away any traces of soap and gently dry with a clean, soft cloth after each use. Rinse completely with water and
dry any overspray. This will maintain the finish and avoid water spotting.
To remove mineral deposits, use a 50/50 solution of white vinegar and water. Do not allow the solution to soak on the
product. Simichrome Polish® contains a protective film to enhance maintenance and is helpful in preventing water spot
buildup. Follow instructions to ensure optimum results.
Never use an abrasive material such as a brush or scouring pad to clean the surface. The use of abrasive cleaners,
cleansers or disinfectants will alter the surface finish and void the warranty.
Do not allow certain materials such as toothpaste, cologne, shaving cream, nail polish remover, vinegar, wine, drain and
glass cleaners to remain on the surface. Prolonged contact will alter surface finishes and void the warranty.
We DO NOT recommend using any household cleaners as many can cause damage to the finish.
Please see the website for care instructions for specific finishes.
1
Remove the mud guard.
Set the handle in the desired off
position and place handle assembly
on the valve. Rotate clockwise
securing the handle assembly and
escutcheon to the wall and engaging
the stem
(see page
5
first).
- If all functions smoothly go to step
#15
- If the handle assembly will not
engage the stem, go to step #4.
- If the handle assembly will not
bottom out on the escutcheon go to
step #10.
3
2
Carefully slide the escutcheon on
valve.
If the handle assembly will
not engage the stem,
remove the handle assembly.
4
a
）
Add the threaded nipple and pressure balance
stem extensions supplied with trim.
b) Set the handle in the desired off position and place
the handle assembly on the valve and rotate clockwise
securing the assembly and escutcheon, engage to the
wall and the stem.
- If all functions smoothly go to step # 15
- If the handle assembly will not bottom out on the
HVFXWFKHRQJRWRVWHS
Cut stem and nipple extensions the
DPRXQWQRWHGLQVWHS1HYHU
cut the stem and nipple while still on
the valve. This may damage the
valve.)
Remove the handle assembly, nipple
and stem extensions.
Re-install the nipple, stem extension
and handle assembly.Go to step
# 15.
Measure and note the
distance ‘YY’ (the distance
between the bottom of the
handle assembly and the
escutcheon).
8
9
6
7
5
11
Remove the handle and escutcheon
assembly, the plate, stem and nipple.
If handle assembly will not bottom
out the escutcheon to the wall,
measure and note the distance
‘XX’(the distance between the
bottom of the handle assembly and
the escutcheon)
Cut stem and nipple the amount
noted in step # 10. (Never cut the
stem and nipple while still on the
valve. This may damage the valve.)
12
13
Re-install the trimmed stem and
nipple on the valve.
Place escutcheon on valve. Thread
on handle assembly to secure
escutcheon.
`
10
Installation Complete.
15
b
b
a
a
a
b
14
Note: For illustration purposes, lever handle version is shown. Please
refer to page 5 for instructions on how remove the lever handle and to
install the cross handle.
Warranty
:
This
Crosswater London
product is covered by a limited lifetime warranty. For full details, terms and conditions please visit our website.
For further information contact
:
Crosswater
London
, 393 Fortune Blvd., Milford, MA 01757
www.crosswater
london.
com
Toll free number: 844-XWATER-1 (844-992-8371) tel: 508-381-
0433
fax: 508-381-6068
email: technical@crosswater
london
.com
Issue date:30092020
