manualshive.com logo in svg

Cross Technologies 3116-145-1600, Инструкция по эксплуатации

Поделиться
Скачать
Cross Technologies 3116-145-1600 Скачать руководство пользователя страница 12

2.5  Menu Settings

2.5.1  Functions
This section describes operation of the front panel controls.  There are three operator switches, the LCD display 
and alarm indicator LEDs.  All functions for the equipment are controlled by these components.  The functions 
are (See Figure 2.4):

Power Up
Normal Display

Menu 1 

Set Input Level Range (option W67 only).

Menu 2 Set 

Gain

Menu 3 

Set Mute

Menu 4 

Set Reference Mode

Menu 5 

Set Reference Offset

Menu 6 Set 

Remote

Menu 7 

Set Remote Interface

Menu 8 

Set RS-485 Address

Save Menu When “R” is selected from any above menu or at the end.

Alarm indications appear on the LEDs (see Figure 2.2).

All program changes must start with the operation of the Menu/Execute switch and must also end with the 
operation of the Menu/Execute switch verified by the “Save Settings?” Menu.  If this sequence is not followed, 
none of the changes will take effect.  If programming is initiated and no operator action takes place for 
approximately 30 seconds (before the final press of the Menu/Execute switch) the display will revert to its 
previous status and you will need to start over.

3116-145-1600 Manual, Rev. 0

 

                      Page 12

    

       05/15/17

Содержание 3116-145-1600




















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды