Crosley CTWMHE12B2 Скачать руководство пользователя страница 6

1

/

2

1

/

2

1

/

2

1

/

2

1

/

2

1

/

2

1

/

2

1

/

2

4

INSTALLATION  INSTRUCTIONS

    Read these instructions completely
    and carefully.

IMPORTANT- 

Save these

instructions for local inspector s use.

IMPORTANT- 

Observe all

governing codes and ordianaces.

Note to Consumer

Keep these

instructions for futrue reference.

Note to Installer

Be sure to leave these

instructions with the Consumer.

Completion time

Approximately 1 hour.

Skill level

Installatio of this appliance

requires basic mechanical skills.

We recommend that two people install
this product.
Proper installation is the responsibility
of the installer.
Product failure due to improper installation
is not covered under the Warranty.
You MUST use all supplied parts and use
proper installation procedures as described
in these instructions when installing this air
conditioner.

    BEFORE YOU BEGIN

Do not, under any circumstances, cut or remove the 
third (ground) prong from the power cord.

CAUTION

Do not change the plug on the power cord of the air 
conditioner.
Aluminum house wiring may present special 
problems- consult a qualified electircian.

When handling unit, be careful to avoid cuts from sharp 
metal edges and aluminum fins on front and rear coils.

Save Carton and these Installation Instructions for future 
reference. The carton is the best way to store unit during 
winter, or when not in use.

NOTE:

Note that the air conditioner dimensions are: 24 inches 
wide, 14 inches high, and 18 inches deep(without front). 
Install Air Conditioner according to these installation 
instructions to achieve the best performance. Save 
these installation instructions for future reference.

NOTE:

 Do not use any screws other than those 

specified here.

Do This First (for existing sleeve)

Items in Kit

You may not need all parts in the kit. Discard unused 
parts.
                                                                                                                

Name
                                                                                                                

Spec.
                                                                                                                

Qty
                                                                                                                

Tapered Spacer Blocks
                                                                                                                

17  Long 

2

Centering/Support Blocks

4      x3     x 1       4

Plastic Divider

1/8 x4     x14     

2

Stuffer Seal 

1   x1     x84       1

Seal  

1   x1     x25     

1   x1      x14     
1   x3/8  x25         

Seal  
Seal  

Seal  

1   x3/8  x14    

1  x3/4  x14   

Seal  

3

3

2

2

2

Trim Frame(side legs)  

Trim Frame(top & bottom legs)  

Ground Wire(green)  
Toothed Washer for grounding 
screw 

Grounding Screw 

Grille(plastic) 
Grille Aluminum  

Nuts(plastic) 

Screw Washer 

Screw 

2
2

1

2

1

1

1

4

4

4

Содержание CTWMHE12B2



























Отзывы: