Cromptons Spinna Winna Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 31

Cromptons Spinna Winna Скачать руководство пользователя страница 10

Spinna Winna Operators Manual

Part No. 990xxx Issue 1

Page 10 of 31

YOUR MACHINE IS NOW SET UP READY FOR USE

17

To adjust the sound volume, locate the

switchboard mounted on the electronics
panel on the LHS of section 1 behind the
payout door. Pressing the switches
repeatedly adjusts the volume in
increments

SWITCH 1 TURNS THE SOUND DOWN

SWITCH 2 TURNS THE SOUND UP

ADJUSTING THE VOLUME

16

This machine is designed to be used

with merchandise on the playfield but we
would strongly recommend that any
merchandise placed on the playfield is kept
clear of the lose holes on either side.
Obstructions in this area could affect the
earning potential of the machine.
Note. Merchandise should not be used on
ticket payout machines

USING MERCHANDISE

15

With the glass doors open and the

machine turned on, spread approx 600
coins evenly over each playfield area and
pusher box. To settle the machine ready for
play it is recommended you feed
approximately 1000 coins through the coin
entries on each section.

PUSHER BOX

FLOATING THE PLAYFIELD

«
...
8
9
10
11
12
...
»

Содержание Spinna Winna
































Отзывы:

Нет отзывов