background image

 

12 

Crimestopper Door Lock Accessories: 
CS-6600DLM:

 Dual-relay plug-in module for Reverse 

Polarity, Positive, or Aftermarket Motors. 

CS-6500DLI:

 Plug-in pulse inverter that converts the 

Negative outputs of the system to Positive type for Positive 
Door Lock systems. 

CS-610S1:

  Aftermarket door lock actuator (motor). 

POWER DOOR LOCKS: (22 gauge wires) 

 

PIN 1: BLUE: 

 (-) Negative pulse for UNLOCK 

PIN 2: RED: 

12V When using external relays (TERM 86) 

PIN 3: GREEN:

 (-) Negative pulse for LOCK 

 
 

DETERMINING  DOOR  LOCK  TYPE:

    We  recommend 

determining  the  type  of  locking  system  the  vehicle  has 
before  connecting  any  wires.  Incorrect  connection  may 
result in damage to the alarm and/or vehicle locking system.  
Door lock information is provided as a guide.  Your vehicle may be different. 

 

Negative Trigger (-): Many Imports; Late model Ford & General Motors 

Negative trigger door lock systems send a Negative (Ground) pulse to existing factory relays to lock and unlock the 
vehicle doors. 

 

Positive Trigger (+): Many General Motors; Chrysler / Dodge / Plymouth 

Positive  trigger  door  lock  systems  send  a  Positive  (12V)  pulse  to  existing  factory  relays  to  lock  and  unlock  the 
vehicle doors. 

 

Reverse Polarity: Many Ford/Lincoln/Mercury/Dodge/Chrysler/Plymouth and early 90’s GM Trucks 

Reverse Polarity systems use no relays, but instead the door lock/unlock motors are controlled directly from the lock 
and  unlock switches in  the door.  The  lock and  unlock wires  rest  at Negative Ground  when  not in use.  When the 
lock or  unlock button is pressed, one  of the circuits is  “Lifted”  and replaced  with +12V causing  a lock or  unlock to 
occur. 

 

Single Wire (Dual Voltage): Late model Chrysler/Dodge/Plymouth Vehicles, some 2000-UP GM 

Dual  Voltage  systems  have  lock/unlock  switches  that  send  varying  levels  of  Positive  voltage  OR  Negative  ground 
current to the SAME wire for both lock and unlock.   When the vehicle’s Body Computer Module (BCM) or door lock 
module senses different voltages on this wire, the system will either lock or unlock.  Single wire door lock systems 
require relays and resistors. 

 

Databus Systems 2003-UP GM Trucks & SUV’s, ‘96-04 Jeep Grand Cherokee 

Databus systems send low current “Data messages” to the door lock controllers on a network in order to lock and 
unlock the vehicle.  To install aftermarket systems in these vehicles, an interface module is required that converts 
the  regular  lock/unlock  pulses  into  “Data  messages”  to  allow  locking  &  unlocking.    Interface  modules  are  sold 
separately. 

 

Содержание Fortress FS-40

































Отзывы: