background image

 

EZ-90 TRANSMITTER / 777TW1/TW2/FM TRANSCEIVER CODE LEARNING 

 

Transmitter/Transceiver Code Learning: (Excludes EZ-91 model without remotes) 

Notes:  Remote Transmitters/Transceivers come pre-programmed from the Factory.  When re-learning remotes or 
adding remotes, ALL your system’s remote codes must be learned at time of programming!!  These systems allow 
storage of up to 4 different remote codes in memory.  The EZ-777TW1/TW2/FM systems include both an LED or LCD 2-
way remote and a “Sidekick” 1-way remote transmitter. “Sidekick” transmitters for the TW1/TW2/FM systems are special 
units which are not compatible with standard EZ-90 remotes.  EZ-90 and EZ-777TW1/TW2/FM remotes are not 
interchangeable. 

 

1.  Open hood (ground the Gray hood pin wire if no hood pin is installed.) 
2.  Turn key to the ON position. (Don not starting vehicle) 
3.  Press Program/Valet button 4 times.  After a few seconds, the unit will flash the parking lights exactly 4 times. 
4. EZ-90: Press Button #1 (Lock) of the transmitter to be learned.  EZ-777TW1/TW2/FM: Both the 

Lock & Unlock

 

buttons must be pressed.  You should get 2 light flashes indicating the code-learn.  Now the unit is waiting for a 2

nd

 

code, so repeat this step as needed with up to 3 additional remotes.  The unit will flash the lights in succession after 
each code learned for up to 4 codes. (2 flashes for the 2

nd

 code, 3 flashes for the 3

rd

 code etc.)  If all 4 codes are 

learned, the unit will automatically exit code learning mode, otherwise turn key OFF and close the hood.  (See 
Diagram Below) 

 

TIP:  When learning 2-Way LED or LCD remotes, wait for a confirmation beep before learning the next remote. 

IGN

OFF

WAIT FOR

4 FLASHES

PRESS 4X's

FLASH 2, 3, or 4 X's

(GRAY WIRE GROUNDED)

EZ-777 2-WAY SYSTEMS

EZ-90

IGN

OFF

PRESS TOGETHER

LOCK &

UNLOCK

PRESS

LOCK ONLY

& "SideKick" REMOTES

COMPLETE

 

 

22 

Содержание Ezee Start EZ-777 FM





























Отзывы: