background image

 

16 

TACHLESS MODE 

 

Your system includes a Tach-less mode that actively monitors and compares the vehicle’s resting voltage versus its 
running voltage each a remote start is performed; [instead of the conventional tach-pulse method].  Smart Tachless 
mode adjusts automatically to maintain optimum efficiency over the life of the life of the installation. 

 

IMPORTANT NOTES: 

(1) SETUP may be required for the Tachless Mode.  If your vehicle has NOT been at rest for a period of time (Hot 

engine), then you must drain the surface charge from the battery.  Unplug main power harness from system, turn 
HEADLIGHTS ON for 4 minutes to drain off excess surface charge on vehicle’s battery then reconnect. 

(2) On the rare occasion that Tachless mode does not operate satisfactorily, change the voltage reference level as 

described below, or use a different mode such as “Tach Reference” mode, or “Timed Crank” mode. 

 
 

TACHLESS ADJUSTMENT: 

In  the  event  Tachless  over-cranks  or  under-cranks  your  starter,  the  settings  can  be  changed.  The  purpose  of 
adjusting the “Smart Tachless” Mode is to raise or lower the voltage reference threshold from the 93% default point.  
Raising or lowering this 93% point should increase or decrease your cranking time respectively.  You can adjust the 
range from 79% to 100% in one percent increments.  Factory default setting [starting point] is in the middle at 93% 
which  should  work  for  most  vehicles.    If  you  feel  you  need  to  fine  tune  the  Tachless  mode,  then  follow  the  steps 
below to adjust its reference level. 

 
 

1.  Open hood (or ground Blue wire if no hood pin is installed) 
2.  Turn the key to the ON position 
3.  Press program button 5 times, after a few seconds the unit will flash the lights 5 times. 
4.  Carefully press the program button 24 times to get to option level 24.  You must get a light flash after each press.  

If the lights didn’t flash, then the unit did not register your button press.  Only count the light flash. 

5.  Press the Lock Button #1 on the remote to decrease by 1% (lights will flash 1X for each press); Press the Unlock 

Button #2 to increase by 1% (lights will flash 2X for each press); Press the Trunk Button #3 to reset to 93% (lights 
will flash 3X).  The unit will stop providing light flashes when you reach the bottom (80%) or the top (100%) of the 
adjustment range. If you lost track, then just press Button #3 to reset back to 93% and begin again. 

6.  Turn Ignition OFF, Close hood (or un-ground the Blue wire) and check operation. 

 
 
 
 
 
 
 
 
 
 

Содержание CS-2011

































Отзывы: