background image

 

RS900/RS901 

SERIES IV

 

RS999 FM FLASHBACK™ 

 

REMOTE ENGINE STARTING SYSTEM 

 

INSTALLATION INSTRUCTIONS 

 

PRE-INSTALLATION CONSIDERATIONS 

 

To ease installation, we suggest that you READ THIS MANUAL and consider the following points before 
beginning your installation: 

 

BEFORE BEGINNING

, check all vehicle manufacturer cautions and warnings regarding electrical service (AIR BAGS, 

ABS BRAKES, ENGINE / BODY COMPUTER AND BATTERY). 

 

PLAN OUT YOUR INSTALLATION

 and determine most suitable locations for all components to be placed. These 

components include:  the module itself, valet/program button, possible relays, and antenna/receiver (RS900/999FM only, 
RS901 model does not include antenna or remotes.)  Allow enough wire to create a service loop with strain relief, should 
servicing be required.  This will also allow easier access and mounting. 

 

DAMAGE 

resulting from incorrect installation or failure to follow guidelines stated in this book will not be covered under 

warranty and subject to repair or replacement charges. 

 

USE A VOLT/OHM METER

 to test and locate all connections.  Test Lights can damage a vehicle’s computer systems. 

 

ADDITIONAL PARTS

, which are not included with this unit, may be needed for your particular vehicle. .  These items may 

include extra relays (Part#CS-402A), General Motors Anti-Theft System Bypass modules for Vats / Passkey® / Passlock® 
Systems, (Part# CS-GMATA II) or Transponder Anti-Theft Adapter modules (Part # CS-TATA). 

 

TECHNICAL SUPPORT: (800) 998-6880 

Monday - Friday 8:00am - 4:30pm Pacific Std. Time 
Web Site: www.crimestopper.com 
E-mail: [email protected] 

 

CRIMESTOPPER SECURITY PRODUCTS, INC. 
1770 S. TAPO STREET, SIMI VALLEY, CA. 93063 

 

REV A - 8.2001 

This device complies with FCC Rules part 15.  Operation is subject to 
the following two conditions:  (1) This device may not cause harmful 
interference, and (2) This device must accept any interference that 
may be received, including interference that may cause undesired 
operation.  The manufacturer is not responsible for any radio or TV 
interference caused by unauthorized modifications to this equipment. 
 Such modification could void the user’s authority to use the 
equipment. 

 

Содержание CoolStart RS-900

















Отзывы: